2.5.3-pre4 ide problems

Its Squash (squash2@dropnet.net)
Thu, 24 Jan 2002 11:21:56 -0600


Greetings,

I have a Compaq Evo n600c laptop, which has Intel ICH3 IDE onboard as well as
CMD646 IDE on my docking station. I have been runing 2.5.1 just fine for a
while. Today I tried 2.5.3-pre4 and I bomb on boot.

The IDE part of dmesg from 2.5.1 says:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3: IDE controller on PCI slot 00:1f.1
PCI: Device 00:1f.1 not available because of resource collisions
ICH3: chipset revision 1
ICH3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x5060-0x5067, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x5068-0x506f, BIOS settings: hdc:DMA, hdd:pio
CMD646: IDE controller on PCI slot 05:07.0
CMD646: chipset revision 7
CMD646: 100% native mode on irq 11
ide2: BM-DMA at 0x2040-0x2047, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x2048-0x204f, BIOS settings: hdg:pio, hdh:pio
hda: TOSHIBA MK2018GAP, ATA DISK drive
hdc: Compaq DVD-ROM DRN-8080B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15

on 2.5.3-pre4, undocked, it says:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3: IDE controller on PCI slot 00:1f.1
PCI: Device 00:1f.1 not available because of resource collisions
ICH3: (ide_setup_pci_device:) Could not enable device.
hda: TOSHIBA MK2018GAP, ATA DISK drive
hdc: Compaq DVD-ROM DRN-8080B, ATAPI CD/DVD-ROM drive
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 39070080 sectors (20004 MB), CHS=2584/240/63
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache

on 2.5.3-pre4, docked, it says:

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3: IDE controller on PCI slot 00:1f.1
PCI: Device 00:1f.1 not available because of resource collisions
ICH3: (ide_setup_pci_device:) Could not enable device.
CMD646: IDE controller on PCI slot 05:07.0
CMD646: chipset revision 7
CMD646: 100% native mode on irq 11
ide0: BM-DMA at 0x2040-0x2047, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2048-0x204f, BIOS settings: hdc:pio, hdd:pio

Josh
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/