Patch: 2.4.18 via-rhine

Andy Carlson (naclos@swbell.net)
Wed, 27 Feb 2002 15:54:09 -0600 (CST)


I took Urban Widmark's via-rhine patch for 2.4.17 that fixed my rhine
interface, and made it apply to 2.4.18.

Andy Carlson |\ _,,,---,,_
naclos@swbell.net ZZZzz /,`.-'`' -. ;-;;,_
Cat Pics: http://andyc.dyndns.org/animal.html |,4- ) )-,_. ,\ ( `'-'
St. Louis, Missouri '---''(_/--' `-'\_)

--- linux-2.4.18-orig/drivers/net/via-rhine.c Mon Feb 25 13:38:00 2002
+++ linux-2.4.18-rhine/drivers/net/via-rhine.c Wed Feb 27 15:17:40 2002
@@ -91,7 +91,7 @@
/* A few user-configurable values.
These may be modified when a driver module is loaded. */

-static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
+static int debug = 3; /* 1 normal messages, 0 quiet .. 7 verbose. */
static int max_interrupt_work = 20;

/* Set the copy breakpoint for the copy-only-tiny-frames scheme.
@@ -329,7 +329,7 @@

enum chip_capability_flags {
CanHaveMII=1, HasESIPhy=2, HasDavicomPhy=4,
- ReqTxAlign=0x10, HasWOL=0x20, };
+ ReqTxAlign=0x10, HasWOL=0x20, HasIntTxUnderFlow=0x40, };

#ifdef USE_MEM
#define RHINE_IOTYPE (PCI_USES_MEM | PCI_USES_MASTER | PCI_ADDR1)
@@ -343,11 +343,13 @@
{ "VIA VT86C100A Rhine", RHINE_IOTYPE, 128,
CanHaveMII | ReqTxAlign },
{ "VIA VT6102 Rhine-II", RHINE_IOTYPE, 256,
- CanHaveMII | HasWOL },
+ CanHaveMII | HasWOL | HasIntTxUnderFlow },
{ "VIA VT3043 Rhine", RHINE_IOTYPE, 128,
CanHaveMII | ReqTxAlign }
};

+#define MII_DAVICOM_DM9101 0x0181b800
+
static struct pci_device_id via_rhine_pci_tbl[] __devinitdata =
{
{0x1106, 0x6100, PCI_ANY_ID, PCI_ANY_ID, 0, 0, VT86C100A},
@@ -384,27 +386,14 @@
IntrRxDone=0x0001, IntrRxErr=0x0004, IntrRxEmpty=0x0020,
IntrTxDone=0x0002, IntrTxAbort=0x0008, IntrTxUnderrun=0x0010,
IntrPCIErr=0x0040,
- IntrStatsMax=0x0080, IntrRxEarly=0x0100, IntrMIIChange=0x0200,
+ IntrStatsMax=0x0080, IntrRxEarly=0x0100,
+ IntrMIIChange=0x0200, IntrTxUnderflow=0x0200, /* see HasIntTxUnderFlow */
IntrRxOverflow=0x0400, IntrRxDropped=0x0800, IntrRxNoBuf=0x1000,
IntrTxAborted=0x2000, IntrLinkChange=0x4000,
IntrRxWakeUp=0x8000,
IntrNormalSummary=0x0003, IntrAbnormalSummary=0xC260,
};

-/* MII interface, status flags.
- Not to be confused with the MIIStatus register ... */
-enum mii_status_bits {
- MIICap100T4 = 0x8000,
- MIICap10100HdFd = 0x7800,
- MIIPreambleSupr = 0x0040,
- MIIAutoNegCompleted = 0x0020,
- MIIRemoteFault = 0x0010,
- MIICapAutoNeg = 0x0008,
- MIILink = 0x0004,
- MIIJabber = 0x0002,
- MIIExtended = 0x0001
-};
-
/* The Rx and Tx buffer descriptors. */
struct rx_desc {
s32 rx_status;
@@ -464,6 +453,7 @@

/* Frequently used values: keep some adjacent for cache effect. */
int chip_id, drv_flags;
+ u8 rev_id;
struct rx_desc *rx_head_desc;
unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
unsigned int cur_tx, dirty_tx;
@@ -480,14 +470,14 @@
u16 advertising; /* NWay media advertisement */
unsigned char phys[MAX_MII_CNT]; /* MII device addresses. */
unsigned int mii_cnt; /* number of MIIs found, but only the first one is used */
- u16 mii_status; /* last read MII status */
+ u32 mii;
struct mii_if_info mii_if;
};

static int mdio_read(struct net_device *dev, int phy_id, int location);
static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
static int via_rhine_open(struct net_device *dev);
-static void via_rhine_check_duplex(struct net_device *dev);
+static int via_rhine_check_duplex(struct net_device *dev);
static void via_rhine_timer(unsigned long data);
static void via_rhine_tx_timeout(struct net_device *dev);
static int via_rhine_start_tx(struct sk_buff *skb, struct net_device *dev);
@@ -679,19 +669,32 @@
goto err_out_unmap;
}

+ /* "3065" specials ... */
if (chip_id == VT6102) {
+ u8 mode3_reg;
/*
* for 3065D, EEPROM reloaded will cause bit 0 in MAC_REG_CFGA
* turned on. it makes MAC receive magic packet
* automatically. So, we turn it off. (D-Link)
*/
- writeb(readb(ioaddr + ConfigA) & 0xFE, ioaddr + ConfigA);
+ writeb(readb(ioaddr + ConfigA) & 0xFE, ioaddr + ConfigA);
+
+ /*
+ * turn on bit2 in PCI configuration register 0x53 ("PCI_REG_MOD
+E3")
+ * 0x04 == MODE3_MIION
+ * FIXME: what does this do?
+ */
+ pci_read_config_byte(pdev, 0x53, &mode3_reg);
+ pci_write_config_byte(pdev, 0x53, mode3_reg | 0x04);
+
}

dev->irq = pdev->irq;

np = dev->priv;
spin_lock_init (&np->lock);
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &(np->rev_id));
np->chip_id = chip_id;
np->drv_flags = via_rhine_chip_info[chip_id].drv_flags;
np->pdev = pdev;
@@ -733,8 +736,9 @@
if (i)
goto err_out_unmap;

- printk(KERN_INFO "%s: %s at 0x%lx, ",
+ printk(KERN_INFO "%s: %s (rev 0x%02x) at 0x%lx, ",
dev->name, via_rhine_chip_info[chip_id].name,
+ np->rev_id,
(pci_flags & PCI_USES_IO) ? ioaddr : memaddr);

for (i = 0; i < 5; i++)
@@ -747,23 +751,30 @@
int phy, phy_idx = 0;
np->phys[0] = 1; /* Standard for this chip. */
for (phy = 1; phy < 32 && phy_idx < MAX_MII_CNT; phy++) {
- int mii_status = mdio_read(dev, phy, 1);
+ int mii_status = mdio_read(dev, phy, MII_BMSR);
if (mii_status != 0xffff && mii_status != 0x0000) {
np->phys[phy_idx++] = phy;
- np->mii_if.advertising = mdio_read(dev, phy, 4);
- printk(KERN_INFO "%s: MII PHY found at address %d, status "
+ np->advertising = mdio_read(dev, phy, MII_ADVERTISE);
+ np->mii = (mdio_read(dev, phy, MII_PHYSID1) << 16) +
+ mdio_read(dev, phy, MII_PHYSID2);
+ printk(KERN_INFO "%s: MII PHY %8.8x found at add
+ress %d, status "
+
"0x%4.4x advertising %4.4x Link %4.4x.\n",
- dev->name, phy, mii_status, np->mii_if.advertising,
- mdio_read(dev, phy, 5));
+ dev->name, np->mii, phy, mii_status, np->advertising,
+ mdio_read(dev, phy, MII_LPA));

- /* set IFF_RUNNING */
- if (mii_status & MIILink)
- netif_carrier_on(dev);
- else
- netif_carrier_off(dev);
+ if ((np->mii & ~0xf) == MII_DAVICOM_DM9101)
+ np->drv_flags |= HasDavicomPhy;
}
}
np->mii_cnt = phy_idx;
+ if (phy_idx == 0) {
+ printk(KERN_WARNING "%s: MII PHY not found -- this devic
+e may "
+ "not operate correctly.\n", dev->name);
+ }
+
np->mii_if.phy_id = np->phys[0];
}

@@ -773,15 +784,14 @@
np->mii_if.full_duplex = 1;
np->default_port = option & 0x3ff;
if (np->default_port & 0x330) {
- /* FIXME: shouldn't someone check this variable? */
- /* np->medialock = 1; */
printk(KERN_INFO " Forcing %dMbs %s-duplex operation.\n",
(option & 0x300 ? 100 : 10),
(option & 0x220 ? "full" : "half"));
if (np->mii_cnt)
- mdio_write(dev, np->phys[0], 0,
- ((option & 0x300) ? 0x2000 : 0) | /* 100mbps? */
- ((option & 0x220) ? 0x0100 : 0)); /* Full duplex? */
+ mdio_write(dev, np->phys[0], MII_BMCR,
+ ((option & 0x300) ? 0x2000 : 0) | /* 100mbps */
+ ((option & 0x220) ? 0x0100 : 0)); /* Full duplex */
+
}
}

@@ -962,10 +972,27 @@
for (i = 0; i < 6; i++)
writeb(dev->dev_addr[i], ioaddr + StationAddr + i);

- /* Initialize other registers. */
+ /* Turn on bit3 (OFSET) in TCR during MAC initialization. */
+ writeb(readb(ioaddr + TxConfig) | 0x08, ioaddr + TxConfig);
+
+ /* Turn off mauto */
+ writeb(readb(ioaddr + MIICmd) & 0x7f, ioaddr + MIICmd);
+ if (np->drv_flags & HasDavicomPhy) {
+ udelay(100);
+ } else {
+ int boguscnt = 0x3fff;
+ while (!(readb(ioaddr + MIIRegAddr) & 0x80) && --boguscnt > 0)
+ ;
+ }
+
writew(0x0006, ioaddr + PCIBusConfig); /* Tune configuration??? */
+
+ /* Clear the lower 4 bits in Config D. */
+ outb(inb(ioaddr + ConfigD) & 0xf0, ioaddr + ConfigD);
+
+
/* Configure the FIFO thresholds. */
- writeb(0x20, ioaddr + TxConfig); /* Initial threshold 32 bytes */
+ writeb(0x20, ioaddr + TxConfig); /* Initial threshold */
np->tx_thresh = 0x20;
np->rx_thresh = 0x60; /* Written in via_rhine_set_rx_mode(). */

@@ -988,13 +1015,33 @@
np->chip_cmd |= CmdFDuplex;
writew(np->chip_cmd, ioaddr + ChipCmd);

+ /* Restart MII auto-negotiation for davidcom phy bug */
+ if (np->drv_flags & HasDavicomPhy) {
+ mdio_write(dev,np->phys[0], MII_BMCR,
+ mdio_read(dev, np->phys[0], MII_BMCR) | 0x1200);
+ /* FIXME: shouldn't we wait for it to complete? Adding silly-delay. */
+ udelay(100);
+ }
+
+
via_rhine_check_duplex(dev);

/* The LED outputs of various MII xcvrs should be configured. */
+ /* For Davicom phys, turn on bit 5 in register 0x16. */
/* For NS or Mison phys, turn on bit 1 in register 0x17 */
/* For ESI phys, turn on bit 7 in register 0x17. */
- mdio_write(dev, np->phys[0], 0x17, mdio_read(dev, np->phys[0], 0x17) |
- (np->drv_flags & HasESIPhy) ? 0x0080 : 0x0001);
+ if (np->drv_flags & HasDavicomPhy) {
+ mdio_write(dev, np->phys[0], 0x16,
+ mdio_read(dev, np->phys[0], 0x16) | 0x20);
+ } else if (np->drv_flags & HasESIPhy) {
+ mdio_write(dev, np->phys[0], 0x17,
+ mdio_read(dev, np->phys[0], 0x17) | 0x80);
+ } else {
+ /* All unknowns get this. Could be a problem. */
+ mdio_write(dev, np->phys[0], 0x17,
+ mdio_read(dev, np->phys[0], 0x17) | 0x01);
+ }
+
}
/* Read and write over the MII Management Data I/O (MDIO) interface. */

@@ -1089,29 +1136,70 @@
return 0;
}

-static void via_rhine_check_duplex(struct net_device *dev)
+static int via_rhine_check_duplex(struct net_device *dev)
{
struct netdev_private *np = dev->priv;
long ioaddr = dev->base_addr;
- int mii_lpa = mdio_read(dev, np->phys[0], MII_LPA);
- int negotiated = mii_lpa & np->mii_if.advertising;
+ int mii_reg;
int duplex;
+ int changed = 0;
+
+ mii_reg = mdio_read(dev, np->phys[0], MII_BMSR);
+ if (mii_reg == 0xffff)
+ return changed;
+
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: MII #%d reports: %4.4x, carrier is: %d\n",
+ dev->name, np->phys[0], mii_reg, netif_carrier_ok(dev));
+ if (!(mii_reg & BMSR_LSTATUS)) {
+ if (netif_carrier_ok(dev)) {
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: MII #%d reports no link. Disabling watchdog.\n",
+ dev->name, np->phys[0]);
+ netif_carrier_off(dev);
+ }
+ } else if (!netif_carrier_ok(dev)) {
+ if (debug > 1)
+ printk(KERN_DEBUG "%s: MII #%d link is back. Enabling watchdog.\n",
+ dev->name, np->phys[0]);
+ netif_carrier_on(dev);
+ }
+
+ if (np->drv_flags & HasDavicomPhy) {
+ /* If the link partner doesn't support autonegotiation
+ * the MII detects it's abilities with the "parallel detection".
+ * Some MIIs update the LPA register to the result of the parallel
+ * detection, some don't.
+ * The Davicom PHY [at least 0181b800] doesn't.
+ * Instead bit 8 and 13 of the BMCR are updated to the result
+ * of the negotiation..
+ */
+ mii_reg = mdio_read(dev, np->phys[0], MII_BMCR);
+ duplex = mii_reg & 0x100;
+ } else {
+ int negotiated;
+ mii_reg = mdio_read(dev, np->phys[0], MII_LPA);
+ negotiated = mii_reg & np->advertising;
+
+ duplex = (negotiated & 0x0100) || ((negotiated & 0x02C0) == 0x0040);
+ }

- if (np->mii_if.duplex_lock || mii_lpa == 0xffff)
- return;
- duplex = (negotiated & 0x0100) || (negotiated & 0x01C0) == 0x0040;
+ if (np->mii_if.duplex_lock || mii_reg == 0xffff)
+ return changed;
if (np->mii_if.full_duplex != duplex) {
np->mii_if.full_duplex = duplex;
+ changed = 1;
if (debug)
printk(KERN_INFO "%s: Setting %s-duplex based on MII #%d link"
" partner capability of %4.4x.\n", dev->name,
- duplex ? "full" : "half", np->phys[0], mii_lpa);
+ duplex ? "full" : "half", np->phys[0], mii_reg);
if (duplex)
np->chip_cmd |= CmdFDuplex;
else
np->chip_cmd &= ~CmdFDuplex;
writew(np->chip_cmd, ioaddr + ChipCmd);
}
+ return changed;
}

@@ -1121,7 +1209,6 @@
struct netdev_private *np = dev->priv;
long ioaddr = dev->base_addr;
int next_tick = 10*HZ;
- int mii_status;

if (debug > 3) {
printk(KERN_DEBUG "%s: VIA Rhine monitor tick, status %4.4x.\n",
@@ -1129,19 +1216,8 @@
}

spin_lock_irq (&np->lock);
-
via_rhine_check_duplex(dev);

- /* make IFF_RUNNING follow the MII status bit "Link established" */
- mii_status = mdio_read(dev, np->phys[0], MII_BMSR);
- if ( (mii_status & MIILink) != (np->mii_status & MIILink) ) {
- if (mii_status & MIILink)
- netif_carrier_on(dev);
- else
- netif_carrier_off(dev);
- }
- np->mii_status = mii_status;
-
spin_unlock_irq (&np->lock);

np->timer.expires = jiffies + next_tick;
@@ -1259,6 +1335,8 @@
long ioaddr;
u32 intr_status;
int boguscnt = max_interrupt_work;
+ struct netdev_private *np = dev->priv;
+ int underflow = np->drv_flags & HasIntTxUnderFlow ? IntrTxUnderflow : 0;

ioaddr = dev->base_addr;

@@ -1275,7 +1353,7 @@
via_rhine_rx(dev);

if (intr_status & (IntrTxDone | IntrTxAbort | IntrTxUnderrun |
- IntrTxAborted))
+ IntrTxAborted | underflow))
via_rhine_tx(dev);

/* Abnormal error summary/uncommon events handlers. */
@@ -1323,7 +1401,13 @@
if (txstatus & 0x0100) np->stats.tx_aborted_errors++;
if (txstatus & 0x0080) np->stats.tx_heartbeat_errors++;
if (txstatus & 0x0002) np->stats.tx_fifo_errors++;
+
/* Transmitter restarted in 'abnormal' handler. */
+ if (txstatus & 0x0900) {
+ /* FIXME: also update TxRingPtr ??? */
+ np->tx_ring[entry].tx_status = cpu_to_le32(DescOwn);
+ }
+
} else {
np->stats.collisions += (txstatus >> 3) & 15;
np->stats.tx_bytes += np->tx_skbuff[entry]->len;
@@ -1465,30 +1549,46 @@
{
struct netdev_private *np = dev->priv;
long ioaddr = dev->base_addr;
+ int mii = np->drv_flags & HasIntTxUnderFlow ? 0 : IntrMIIChange;
+ int underflow = np->drv_flags & HasIntTxUnderFlow ? IntrTxUnderflow : 0;

spin_lock (&np->lock);

- if (intr_status & (IntrMIIChange | IntrLinkChange)) {
+ if (intr_status & (mii | IntrLinkChange)) {
+ int changed;
+ if (debug)
+ printk(KERN_DEBUG "%s: Link change, status=%4.4x\n",
+ dev->name, intr_status);
if (readb(ioaddr + MIIStatus) & 0x02) {
/* Link failed, restart autonegotiation. */
if (np->drv_flags & HasDavicomPhy)
mdio_write(dev, np->phys[0], MII_BMCR, 0x3300);
+ /* Will the new link status be reported late? */
+ changed = 0;
+
} else
- via_rhine_check_duplex(dev);
- if (debug)
+ changed = via_rhine_check_duplex(dev);
+ if (debug && changed)
+
printk(KERN_ERR "%s: MII status changed: Autonegotiation "
"advertising %4.4x partner %4.4x.\n", dev->name,
- mdio_read(dev, np->phys[0], MII_ADVERTISE),
- mdio_read(dev, np->phys[0], MII_LPA));
+ mdio_read(dev, np->phys[0], MII_ADVERTISE),
+ mdio_read(dev, np->phys[0], MII_LPA));
+
}
if (intr_status & IntrStatsMax) {
np->stats.rx_crc_errors += readw(ioaddr + RxCRCErrs);
np->stats.rx_missed_errors += readw(ioaddr + RxMissed);
clear_tally_counters(ioaddr);
}
- if (intr_status & IntrTxAbort) {
+ if (intr_status & (underflow | IntrTxAbort)) {
+
/* Stats counted in Tx-done handler, just restart Tx. */
writew(CmdTxDemand | np->chip_cmd, dev->base_addr + ChipCmd);
+ if (debug > 1)
+ printk(KERN_INFO "%s: Transmitter underflow?, status %4.4x.\n",
+ dev->name, intr_status);
+
}
if (intr_status & IntrTxUnderrun) {
if (np->tx_thresh < 0xE0)
@@ -1497,8 +1597,7 @@
printk(KERN_INFO "%s: Transmitter underrun, increasing Tx "
"threshold setting to %2.2x.\n", dev->name, np->tx_thresh);
}
- if ((intr_status & ~( IntrLinkChange | IntrStatsMax |
- IntrTxAbort | IntrTxAborted))) {
+ if ((intr_status & ~( IntrLinkChange | IntrStatsMax | IntrTxAborted))) {
if (debug > 1)
printk(KERN_ERR "%s: Something Wicked happened! %4.4x.\n",
dev->name, intr_status);

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/