The ISA drivers are often old and unmaintained, this way one can easier
ignore them.
It also makes some more drivers dependent on CONFIG_ISA, mostly
in drivers/scsi and sound. I did this by looking at the source code
and double checked the result with linux-kernel.
VLB only drivers are also included in CONFIG_ISA, under the assumption
that VLB boxes always have ISA slots.
The configuration changes are not complete, some subsystems are missing
like ISDN. I'm hoping the maintainers will add it there too.
The main motivation is that I can turn off CONFIG_ISA for x86-64 where
no ISA slots exist. The ISA drivers are often not 64bit safe and compile
with an incredible number of warnings only.
Patch for 2.5.15.
-Andi
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/char/Config.in linux/drivers/char/Config.in
--- linux-vanilla/drivers/char/Config.in Sun May 12 19:37:24 2002
+++ linux/drivers/char/Config.in Fri May 10 12:09:04 2002
@@ -39,7 +39,7 @@ if [ "$CONFIG_SERIAL_NONSTANDARD" = "y"
if [ "$CONFIG_DIGIEPCA" = "n" ]; then
tristate ' Digiboard PC/Xx Support' CONFIG_DIGI
fi
- tristate ' Hayes ESP serial port support' CONFIG_ESPSERIAL
+ dep_tristate ' Hayes ESP serial port support' CONFIG_ESPSERIAL CONFIG_ISA
tristate ' Moxa Intellio support' CONFIG_MOXA_INTELLIO
tristate ' Moxa SmartIO support' CONFIG_MOXA_SMARTIO
if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/ide/Config.in linux/drivers/ide/Config.in
--- linux-vanilla/drivers/ide/Config.in Sun May 12 19:37:25 2002
+++ linux/drivers/ide/Config.in Fri May 10 12:09:05 2002
@@ -125,7 +125,8 @@ if [ "$CONFIG_BLK_DEV_IDE" != "n" ]; the
EXT_DIRECT CONFIG_IDE_EXT_DIRECT" 8xx_PCCARD
fi
- bool ' Other IDE chipset support' CONFIG_IDE_CHIPSETS
+ # assume no ISA -> also no VLB
+ dep_bool ' Other ISA/VLB IDE chipset support' CONFIG_IDE_CHIPSETS CONFIG_ISA
if [ "$CONFIG_IDE_CHIPSETS" = "y" ]; then
comment 'Note: most of these also require special kernel boot parameters'
bool ' ALI M14xx support' CONFIG_BLK_DEV_ALI14XX
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/media/radio/Config.in linux/drivers/media/radio/Config.in
--- linux-vanilla/drivers/media/radio/Config.in Sun Apr 14 21:18:54 2002
+++ linux/drivers/media/radio/Config.in Thu May 9 20:07:45 2002
@@ -4,6 +4,7 @@
mainmenu_option next_comment
comment 'Radio Adapters'
+if [ "$CONFIG_ISA" = "y" ]; then
dep_tristate ' ADS Cadet AM/FM Tuner' CONFIG_RADIO_CADET $CONFIG_VIDEO_DEV
dep_tristate ' AIMSlab RadioTrack (aka RadioReveal) support' CONFIG_RADIO_RTRACK $CONFIG_VIDEO_DEV
if [ "$CONFIG_RADIO_RTRACK" = "y" ]; then
@@ -21,9 +22,11 @@ dep_tristate ' GemTek Radio Card suppor
if [ "$CONFIG_RADIO_GEMTEK" = "y" ]; then
hex ' GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)' CONFIG_RADIO_GEMTEK_PORT 34c
fi
+fi
dep_tristate ' GemTek PCI Radio Card support' CONFIG_RADIO_GEMTEK_PCI $CONFIG_VIDEO_DEV $CONFIG_PCI
dep_tristate ' Guillemot MAXI Radio FM 2000 radio' CONFIG_RADIO_MAXIRADIO $CONFIG_VIDEO_DEV
dep_tristate ' Maestro on board radio' CONFIG_RADIO_MAESTRO $CONFIG_VIDEO_DEV
+if [ "$CONFIG_ISA" = "y" ]; then
dep_tristate ' miroSOUND PCM20 radio' CONFIG_RADIO_MIROPCM20 $CONFIG_VIDEO_DEV $CONFIG_SOUND_ACI_MIXER
dep_tristate ' miroSOUND PCM20 radio RDS user interface (EXPERIMENTAL)' CONFIG_RADIO_MIROPCM20_RDS $CONFIG_RADIO_MIROPCM20 $CONFIG_EXPERIMENTAL
dep_tristate ' SF16FMI Radio' CONFIG_RADIO_SF16FMI $CONFIG_VIDEO_DEV
@@ -48,6 +51,7 @@ fi
dep_tristate ' Zoltrix Radio' CONFIG_RADIO_ZOLTRIX $CONFIG_VIDEO_DEV
if [ "$CONFIG_RADIO_ZOLTRIX" = "y" ]; then
hex ' ZOLTRIX I/O port (0x20c or 0x30c)' CONFIG_RADIO_ZOLTRIX_PORT 20c
+fi
fi
endmenu
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/net/hamradio/Config.in linux/drivers/net/hamradio/Config.in
--- linux-vanilla/drivers/net/hamradio/Config.in Sun Apr 14 21:18:42 2002
+++ linux/drivers/net/hamradio/Config.in Thu May 9 19:59:53 2002
@@ -4,8 +4,10 @@ dep_tristate 'Serial port KISS driver' C
dep_tristate 'Serial port 6PACK driver' CONFIG_6PACK $CONFIG_AX25
dep_tristate 'BPQ Ethernet driver' CONFIG_BPQETHER $CONFIG_AX25
-dep_tristate 'High-speed (DMA) SCC driver for AX.25' CONFIG_DMASCC $CONFIG_AX25
-dep_tristate 'Z8530 SCC driver' CONFIG_SCC $CONFIG_AX25
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'High-speed (DMA) SCC driver for AX.25' CONFIG_DMASCC $CONFIG_AX25
+ dep_tristate 'Z8530 SCC driver' CONFIG_SCC $CONFIG_AX25
+fi
if [ "$CONFIG_SCC" != "n" ]; then
bool ' additional delay for PA0HZP OptoSCC compatible boards' CONFIG_SCC_DELAY
bool ' support for TRX that feedback the tx signal to rx' CONFIG_SCC_TRXECHO
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/net/wan/Config.in linux/drivers/net/wan/Config.in
--- linux-vanilla/drivers/net/wan/Config.in Mon May 6 13:11:57 2002
+++ linux/drivers/net/wan/Config.in Thu May 9 19:59:54 2002
@@ -9,11 +9,12 @@ bool 'Wan interfaces support' CONFIG_WAN
if [ "$CONFIG_WAN" = "y" ]; then
# There is no way to detect a comtrol sv11 - force it modular for now.
+ if [ "$CONFIG_ISA" = "y" ]; then
dep_tristate ' Comtrol Hostess SV-11 support' CONFIG_HOSTESS_SV11 m
-
# The COSA/SRP driver has not been tested as non-modular yet.
dep_tristate ' COSA/SRP sync serial boards support' CONFIG_COSA m
+ fi
#
# COMX drivers
diff -burpN -X ../../KDIFX -x *-o linux-vanilla/drivers/scsi/Config.in linux/drivers/scsi/Config.in
--- linux-vanilla/drivers/scsi/Config.in Fri May 3 13:22:27 2002
+++ linux/drivers/scsi/Config.in Fri May 10 01:12:53 2002
@@ -42,11 +42,17 @@ fi
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate '3ware Hardware ATA-RAID support' CONFIG_BLK_DEV_3W_XXXX_RAID $CONFIG_SCSI
fi
-dep_tristate '7000FASST SCSI support' CONFIG_SCSI_7000FASST $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate '7000FASST SCSI support' CONFIG_SCSI_7000FASST $CONFIG_SCSI
+fi
dep_tristate 'ACARD SCSI support' CONFIG_SCSI_ACARD $CONFIG_SCSI
-dep_tristate 'Adaptec AHA152X/2825 support' CONFIG_SCSI_AHA152X $CONFIG_SCSI
-dep_tristate 'Adaptec AHA1542 support' CONFIG_SCSI_AHA1542 $CONFIG_SCSI
-dep_tristate 'Adaptec AHA1740 support' CONFIG_SCSI_AHA1740 $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'Adaptec AHA152X/2825 support' CONFIG_SCSI_AHA152X $CONFIG_SCSI
+ dep_tristate 'Adaptec AHA1542 support' CONFIG_SCSI_AHA1542 $CONFIG_SCSI
+fi
+if [ "$CONFIG_EISA" = "y" ]; then
+ dep_tristate 'Adaptec AHA1740 support' CONFIG_SCSI_AHA1740 $CONFIG_SCSI
+fi
source drivers/scsi/aic7xxx/Config.in
if [ "$CONFIG_SCSI_AIC7XXX" != "y" ]; then
dep_tristate 'Old Adaptec AIC7xxx support' CONFIG_SCSI_AIC7XXX_OLD $CONFIG_SCSI
@@ -56,10 +62,16 @@ if [ "$CONFIG_SCSI_AIC7XXX" != "y" ]; th
bool ' Collect statistics to report in /proc' CONFIG_AIC7XXX_OLD_PROC_STATS
fi
fi
-dep_tristate 'Adaptec I2O RAID support ' CONFIG_SCSI_DPT_I2O $CONFIG_SCSI
+# All the I2O code and drivers do not seem to be 64bit safe.
+if [ "$CONFIG_X86_64" != "y" ]; then
+ dep_tristate 'Adaptec I2O RAID support ' CONFIG_SCSI_DPT_I2O $CONFIG_SCSI
+fi
dep_tristate 'AdvanSys SCSI support' CONFIG_SCSI_ADVANSYS $CONFIG_SCSI
dep_tristate 'Always IN2000 SCSI support' CONFIG_SCSI_IN2000 $CONFIG_SCSI
-dep_tristate 'AM53/79C974 PCI SCSI support' CONFIG_SCSI_AM53C974 $CONFIG_SCSI $CONFIG_PCI
+# does not use pci dma and seems to be isa/onboard only for old machines
+if [ "$CONFIG_X86_64" != "y" ]; then
+ dep_tristate 'AM53/79C974 PCI SCSI support' CONFIG_SCSI_AM53C974 $CONFIG_SCSI $CONFIG_PCI
+fi
dep_tristate 'AMI MegaRAID support' CONFIG_SCSI_MEGARAID $CONFIG_SCSI
dep_tristate 'BusLogic SCSI support' CONFIG_SCSI_BUSLOGIC $CONFIG_SCSI
@@ -70,7 +82,9 @@ if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'Compaq Fibre Channel 64-bit/66Mhz HBA support' CONFIG_SCSI_CPQFCTS $CONFIG_SCSI
fi
dep_tristate 'DMX3191D SCSI support' CONFIG_SCSI_DMX3191D $CONFIG_SCSI $CONFIG_PCI
-dep_tristate 'DTC3180/3280 SCSI support' CONFIG_SCSI_DTC3280 $CONFIG_SCSI
+if [ "$CONFIG_ISA" != "y" ]; then
+ dep_tristate 'DTC3180/3280 SCSI support' CONFIG_SCSI_DTC3280 $CONFIG_SCSI
+fi
dep_tristate 'EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support' CONFIG_SCSI_EATA $CONFIG_SCSI
if [ "$CONFIG_SCSI_EATA" != "n" ]; then
bool ' enable tagged command queueing' CONFIG_SCSI_EATA_TAGGED_QUEUE
@@ -111,7 +125,9 @@ if [ "$CONFIG_PARPORT" != "n" ]; then
bool ' ppa/imm option - Assume slow parport control register' CONFIG_SCSI_IZIP_SLOW_CTR
fi
fi
-dep_tristate 'NCR53c406a SCSI support' CONFIG_SCSI_NCR53C406A $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'NCR53c406a SCSI support' CONFIG_SCSI_NCR53C406A $CONFIG_SCSI
+fi
if [ "$CONFIG_MCA" = "y" ]; then
dep_tristate 'NCR Dual 700 MCA SCSI support' CONFIG_SCSI_NCR_D700 $CONFIG_SCSI
if [ "$CONFIG_SCSI_NCR_D700" != "n" ]; then
@@ -164,11 +180,17 @@ fi
if [ "$CONFIG_MCA" = "y" ]; then
dep_tristate 'NCR MCA 53C9x SCSI support' CONFIG_SCSI_MCA_53C9X $CONFIG_SCSI
fi
-dep_tristate 'PAS16 SCSI support' CONFIG_SCSI_PAS16 $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'PAS16 SCSI support' CONFIG_SCSI_PAS16 $CONFIG_SCSI
+fi
dep_tristate 'PCI2000 support' CONFIG_SCSI_PCI2000 $CONFIG_SCSI
dep_tristate 'PCI2220i support' CONFIG_SCSI_PCI2220I $CONFIG_SCSI
-dep_tristate 'PSI240i support' CONFIG_SCSI_PSI240I $CONFIG_SCSI
-dep_tristate 'Qlogic FAS SCSI support' CONFIG_SCSI_QLOGIC_FAS $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'PSI240i support' CONFIG_SCSI_PSI240I $CONFIG_SCSI
+fi
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'Qlogic FAS SCSI support' CONFIG_SCSI_QLOGIC_FAS $CONFIG_SCSI
+fi
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'Qlogic ISP SCSI support' CONFIG_SCSI_QLOGIC_ISP $CONFIG_SCSI
dep_tristate 'Qlogic ISP FC SCSI support' CONFIG_SCSI_QLOGIC_FC $CONFIG_SCSI
@@ -177,24 +199,31 @@ if [ "$CONFIG_PCI" = "y" ]; then
fi
dep_tristate 'Qlogic QLA 1280 SCSI support' CONFIG_SCSI_QLOGIC_1280 $CONFIG_SCSI
fi
-if [ "$CONFIG_X86" = "y" ]; then
+if [ "$CONFIG_X86" = "y" -a "$CONFIG_ISA" = "y" ]; then
dep_tristate 'Seagate ST-02 and Future Domain TMC-8xx SCSI support' CONFIG_SCSI_SEAGATE $CONFIG_SCSI
fi
-dep_tristate 'Simple 53c710 SCSI support (Compaq, NCR machines)' CONFIG_SCSI_SIM710 $CONFIG_SCSI
-dep_tristate 'Symbios 53c416 SCSI support' CONFIG_SCSI_SYM53C416 $CONFIG_SCSI
+# definitely looks note 64bit safe:
+if [ "$CONFIG_ISA" = "y" -o "$CONFIG_MCA" = "y" -a "$CONFIG_X86_64" != "y" ]; then
+ dep_tristate 'Simple 53c710 SCSI support (Compaq, NCR machines)' CONFIG_SCSI_SIM710 $CONFIG_SCSI
+fi
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'Symbios 53c416 SCSI support' CONFIG_SCSI_SYM53C416 $CONFIG_SCSI
+fi
if [ "$CONFIG_PCI" = "y" ]; then
dep_tristate 'Tekram DC390(T) and Am53/79C974 SCSI support' CONFIG_SCSI_DC390T $CONFIG_SCSI
if [ "$CONFIG_SCSI_DC390T" != "n" ]; then
bool ' _omit_ support for non-DC390 adapters' CONFIG_SCSI_DC390T_NOGENSUPP
fi
fi
-dep_tristate 'Trantor T128/T128F/T228 SCSI support' CONFIG_SCSI_T128 $CONFIG_SCSI
+if [ "$CONFIG_ISA" = "y" ]; then
+ dep_tristate 'Trantor T128/T128F/T228 SCSI support' CONFIG_SCSI_T128 $CONFIG_SCSI
+fi
dep_tristate 'UltraStor 14F/34F support' CONFIG_SCSI_U14_34F $CONFIG_SCSI
- if [ "$CONFIG_SCSI_U14_34F" != "n" ]; then
+if [ "$CONFIG_SCSI_U14_34F" != "n" ]; then
bool ' enable elevator sorting' CONFIG_SCSI_U14_34F_LINKED_COMMANDS
int ' maximum number of queued commands' CONFIG_SCSI_U14_34F_MAX_TAGS 8
- fi
-if [ "$CONFIG_X86" = "y" ]; then
+fi
+if [ "$CONFIG_X86" = "y" -a "$CONFIG_ISA" = "y" ]; then
dep_tristate 'UltraStor SCSI support' CONFIG_SCSI_ULTRASTOR $CONFIG_SCSI
fi
#
--- linux-vanilla/arch/i386/config.in Mon May 6 13:11:55 2002
+++ linux/arch/i386/config.in Sun May 12 20:28:38 2002
@@ -5,7 +5,6 @@
mainmenu_name "Linux Kernel Configuration"
define_bool CONFIG_X86 y
-define_bool CONFIG_ISA y
define_bool CONFIG_SBUS n
define_bool CONFIG_UID16 y
@@ -238,6 +237,7 @@
define_bool CONFIG_PCI_DIRECT y
fi
fi
+ bool 'ISA support' CONFIG_ISA
fi
source drivers/pci/Config.in
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/