Cheers
jlk
On Wednesday 07 August 2002 07:35 pm, Mark Cuss wrote:
> Hello all,
>
> Please accept my apologies if this question has already been answered....
>
> I have a new Pentium 4 computer and I can't get the DMA working for hard
> disk transfers. Specifically, its a Dell Dimension 4500 with a Pentium 4
> 2.26 GHz processor (Northwood) and an 845 (Brookdale) chipset. RedHat
> 7.3....
>
> I noticed that the hard disk transfers were very slow. I tried to set up
> DMA with hdparm - see below:
>
> [root@yoda ide]# hdparm /dev/hda
>
> /dev/hda:
> multcount = 16 (on)
> I/O support = 0 (default 16-bit)
> unmaskirq = 0 (off)
> using_dma = 0 (off)
> keepsettings = 0 (off)
> nowerr = 0 (off)
> readonly = 0 (off)
> readahead = 8 (on)
> geometry = 4866/255/63, sectors = 78177792, start = 0
> busstate = 1 (on)
> [root@yoda ide]# hdparm -d1 /dev/hda
>
> /dev/hda:
> setting using_dma to 1 (on)
> HDIO_SET_DMA failed: Operation not permitted
> using_dma = 0 (off)
> [root@yoda ide]#
>
> I thought that perhaps the chipset had changed between this Northwood
> machine an the older core - I have a P4 1.8 GHz machine that DMA works fine
> on. I upgraded to kernel 2.4.19 with no change.
>
> The IDE controller (according to Windows XP....) is an Intel 82801DB Ultra
> ATA Storage Controller - 24CB. I've included the lspci --vvx listing from
> the problem machine below - my aplogies for the long list. If anyone has
> any suggestions I'd really appreciate them...
>
> Thanks....
>
> Mark
>
> lspci listing:
>
> 00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge
> (rev 11)
> Subsystem: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [e4] #09 [a104]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>
> 00: 86 80 30 1a 06 01 90 20 11 00 00 06 00 00 00 00
> 10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 30 1a
> 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
>
> 00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge
> (rev 11) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> Memory behind bridge: fc700000-fe7fffff
> Prefetchable memory behind bridge: dc300000-ec4fffff
> BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
> 00: 86 80 31 1a 07 01 a0 00 11 00 04 06 00 40 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 a0 22
> 20: 70 fc 70 fe 30 dc 40 ec 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 00
>
> 00:1d.0 USB Controller: Intel Corp.: Unknown device 24c2 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at e800 [size=32]
> 00: 86 80 c2 24 05 00 80 02 01 00 03 0c 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 e8 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
>
> 00:1d.1 USB Controller: Intel Corp.: Unknown device 24c4 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 5
> Region 4: I/O ports at e880 [size=32]
> 00: 86 80 c4 24 05 00 80 02 01 00 03 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 81 e8 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
>
> 00:1d.2 USB Controller: Intel Corp.: Unknown device 24c7 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 9
> Region 4: I/O ports at ec00 [size=32]
> 00: 86 80 c7 24 05 00 80 02 01 00 03 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 ec 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 03 00 00
>
> 00:1d.7 USB Controller: Intel Corp.: Unknown device 24cd (rev 01) (prog-if
> 20 [EHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 10
> Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [2080]
> 00: 86 80 cd 24 06 01 90 02 01 20 03 0c 00 00 00 00
> 10: 00 fc bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00
>
> 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 81) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR+
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fe800000-feafffff
> Prefetchable memory behind bridge: ec500000-ec5fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 00: 86 80 4e 24 07 01 80 80 81 00 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 02 02 20 d0 d0 80 22
> 20: 80 fe a0 fe 50 ec 50 ec 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
>
> 00:1f.0 ISA bridge: Intel Corp.: Unknown device 24c0 (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> 00: 86 80 c0 24 0f 01 80 02 01 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:1f.1 IDE interface: Intel Corp.: Unknown device 24cb (rev 01) (prog-if
> 8a [Master SecP PriP])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at <unassigned> [size=8]
> Region 1: I/O ports at <unassigned> [size=4]
> Region 2: I/O ports at <unassigned> [size=8]
> Region 3: I/O ports at <unassigned> [size=4]
> Region 4: I/O ports at ffa0 [size=16]
> Region 5: Memory at 20000000 (32-bit, non-prefetchable) [disabled]
> [size=1K]
> 00: 86 80 cb 24 05 00 80 02 01 8a 01 01 00 00 00 00
> 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
> 20: a1 ff 00 00 00 00 00 20 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
>
> 00:1f.3 SMBus: Intel Corp.: Unknown device 24c3 (rev 01)
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 3
> Region 4: I/O ports at e480 [size=32]
> 00: 86 80 c3 24 01 00 80 02 01 00 05 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 81 e4 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4
> Ti4200] (rev a3) (prog-if 00 [VGA])
> Subsystem: nVidia Corporation: Unknown device 0132
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
> Region 2: Memory at ec480000 (32-bit, prefetchable) [size=512K]
> Expansion ROM at fe7e0000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
> 00: de 10 53 02 07 00 b0 02 a3 00 00 03 00 f8 00 00
> 10: 00 00 00 fd 08 00 00 e0 08 00 48 ec 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 32 01
> 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 05 01
>
> 02:00.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev
> 10)
> Subsystem: Intel Corp.: Unknown device 0071
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min, 14000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at dc00 [size=64]
> Region 2: Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
> Expansion ROM at feae0000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> 00: 86 80 29 12 17 01 90 02 10 00 00 02 08 40 00 00
> 10: 00 f0 af fe 01 dc 00 00 00 00 ac fe 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 71 00
> 30: 00 00 ae fe dc 00 00 00 00 00 00 00 0b 01 08 38
>
> 02:02.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24
> [CrystalClear SoundFusion Audio Accelerator] (rev 01)
> Subsystem: Voyetra Technologies: Unknown device 3357
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (1000ns min, 6000ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at feafd000 (32-bit, non-prefetchable) [size=4K]
> Region 1: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 13 10 03 60 06 01 10 04 01 00 01 04 00 40 00 00
> 10: 00 d0 af fe 00 00 90 fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 53 50 57 33
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 04 18
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-- John L. Korpi, Ph.D. -- Senior Scientist, Networks & Infrastructure NeuStar, Inc. Voice: 1.216.241.2919, 1.703.435.0682 Mobile: 1.216.233.3042 Pager: 1.800.398.2959- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/