> Eric W. Biederman wrote:
> >Russell King <rmk@arm.linux.org.uk> writes:
>
> >> "rebooting" in this particular case is "turn MMU off, jump to location 0"
> >And for x86 it is turn MMU off, jump to location 0xffff0.
>
>
> The default reboot method of linux-2.5.42 on x86 is to have the
> keyboard controller do a reset.
Resetting the cpu != resetting the system. And the keyboard controller
only does a cpu level reset. Which is basically a convoluted way to jump
to: 0xfffffff0.
> If you want to reboot by jumping to ffff00,
> you have to pass "reboot=b" unless you are running on one of three specific
> models of computers: the Dell PowerEdge 300, 1300 or 2400
> (linux-2.5.42/arch/i386/kernel/dmi-scan.c line 522). Here is the
> relevant excerpt from machine_restart in linux-2.5.42/arch/i386/reboot.c:
>
> if(!reboot_thru_bios) {
> /* rebooting needs to touch the page at absolute addr 0 */
> *((unsigned short *)__va(0x472)) = reboot_mode;
> for (;;) {
> int i;
> for (i=0; i<100; i++) {
> kb_wait();
> udelay(50);
> outb(0xfe,0x64); /* pulse reset low */
> udelay(50);
> }
> /* That didn't work - force a triple fault.. */
> __asm__ __volatile__("lidt %0": :"m" (no_idt));
> __asm__ __volatile__("int3");
> }
> }
Please note the write to: 0x40:0x72. If this was a full machine reset
this would not make sense as memory would need to be reinitialized
making it unsafe to keep values in ram.
> In another message, you wrote:
> >Exactly an in spec, PC does not need to ground RST# on reboot.
>
> By "as in spec", were you referring to my quotation from _PCI
> System Architecture, 4th Ed._ by Shanley and Anderson or are saying
> that there is a specification that supports your statement that "a PC
> does not need to ground RST# on reboot." If the latter, I would
> appreciate it if you would identify that specification and the
> appropriate section with it for verification.
I'd love to but mostly I was referring to the de facto standard for
pc architecture. Which I don't know if anyone ever wrote down, all
in one place.
> Elsewhere you wrote:
> >Additionally it was decided quite a
> >while ago that calling device->remove() was the correct way to
> >accomplish this.
>
> Do you remember where this "was decided?" If it was on an
> archived mailing list, do you remember approximately when and what the
> subject line might be? I'd like to look at this discussion both to
> verify you statement and to avoid repetition.
No. I was not in on that conversation. However given the fact it
is all over the documentation. And has been in the kernel for quite
a while now. I tracked it as early as 2.5.30.
This is both device_shutdown in the reboot path,
and device_shutdown calling ->remove()
> In another message you wrote:
> >machine_restart returns control to the BIOS.
> >It works this way on both x86 and alpha. And the BIOS does
> >not always toggle the RESET line on the machine. The frequent case
> >of devices not working in Linux after rebooting from windows, and
> >visa versa is evidence of this. On alpha the SRM doesn't even
> >pretend to reset the machine.
>
> Here you are talk first about doing a warm reboot from Windows
> to Linux and the device does not work. That sounds like a quirky
> device.
No it sounds like a driver that either can or cannot handle devices
in an arbitrary state.
> Also, you have failed to show that this is a device where the
> Linux driver's ->remove() function solves the problem and that there
> are so many of these devices that (where the remove function *does*
> solve the problem and there is no reboot notifier) that it would be
> impractical change those drivers.
I do not feel I need to defend the status quo. It is you who are proposing
a change that needs to support why using ->remove() is a bad way to go.
I will just say that shutting devices in a depth first manner is a lot safer,
and more reliable than a random walk, you will get with a reboot notifier.
> If the problem is that the warm reboot procedure failed to
> "stop any ongoing DMA, etc." as you put it, then failure mode that you
> would more typically expect would be memory corruption, manifesting
> itself as random of other programs, not getting through the reboot
> process half of the time, etc.
You would only see it on the boot up side. Not placing devices in
a consistent state so another os can talk to them is significant as well.
> The underlying trade-off is that if I want to reboot fast, I
> should not have to call a bunch of hotplug routines that have to do a
> lot of book keeping because they have to assume that the computer may
> continue to run user level programs indefinitely after they return
> (things like deallocating memory, unregistering devfs inodes, etc.).
I would be very surprised if this showed up in practice. If Russell King
makes the argument about excess book keeping slowing things down. I
will buy it because he runs on some very slow machines. Personally I
doubt anything will be user noticeable.
> On the other hand, if I want to halt, I really do want the disks to be
> spun down even if my motherboard does not do a master power-off from
> software. Doing that requires that the power management request that
> reboot makes differ from the one that halt makes. So they could
> not both be just "device_shtudown();".
So you want to send device_suspend(?, SUSPEND_POWER_DOWN) on a halt.
Or do a software shutdown thing.
Whoever mapped the SUSPEND_SHUT_DOWN to SUSPEND_POWER_DOWN very much
had it wrong when that code was merged with 2.5.42.
Mostly it looks to me that you have a problem with IDE driver spinning
down disks on reboot. That change also is new in 2.5.41.
Eric
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/