--=_courier-8070-1048069329-0001-2
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
Hi,
ISD200 based hard drive bay doesn't work with 2.4 & 2.5,
can someone assist me with it?
Kernel message log appended.
Best regards.
-- Andrey Panin | Embedded systems software developer pazke@orbita1.ru | PGP key: wwwkeys.pgp.net--=_courier-8070-1048069329-0001-2 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="usb.log"
drivers/usb/core/usb.c: registered new driver hub drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.0 PCI: Found IRQ 11 for device 00:1f.2 PCI: Setting latency timer of device 00:1f.2 to 64 uhci-hcd 00:1f.2: Intel Corp. 82801AA USB uhci-hcd 00:1f.2: irq 11, io base 0000d000 uhci-hcd 00:1f.2: new USB bus registered, assigned bus number 1 hub 1-0:0: USB hub found hub 1-0:0: 2 ports detected hub 1-0:0: debounce: port 2: delay 100ms stable 4 status 0x101 hub 1-0:0: new USB device on port 2, assigned address 2 Initializing USB Mass Storage driver... usb-storage: act_altsetting is 0 usb-storage: id_index calculated to be: 32 usb-storage: Array length appears to be: 81 usb-storage: Vendor: In-System usb-storage: Product: USB/IDE Bridge (ATA/ATAPI) usb-storage: USB Mass Storage device detected usb-storage: Endpoints: In: 0xc336b934 Out: 0xc336b920 Int: 0xc336b948 (Period 32) usb-storage: GetMaxLUN command result is 1, data is 0 usb-storage: Transport: Bulk usb-storage: Protocol: ISD200 ATA/ATAPI usb-storage: Allocating usb_ctrlrequest usb-storage: Allocating URB usb-storage: Allocating scatter-gather request block usb-storage: ISD200 Initialization... usb-storage: Entering isd200_get_inquiry_data usb-storage: Entering isd200_manual_enum usb-storage: Entering isd200_read_config usb-storage: usb_stor_ctrl_transfer(): rq=02 rqtype=c0 value=0000 index=02 len=8 usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: Retrieved the following ISD200 Config Data: usb-storage: Event Notification: 0x0 usb-storage: External Clock: 0x0 usb-storage: ATA Init Timeout: 0x19 usb-storage: ATAPI Command Block Size: 0x0 usb-storage: Master/Slave Selection: 0x0 usb-storage: ATAPI Reset: 0x0 usb-storage: ATA Timing: 0x1 usb-storage: ATA Major Command: 0x24 usb-storage: ATA Minor Command: 0x24 usb-storage: Init Status: 0x0 usb-storage: Config Descriptor 2: 0x0 usb-storage: Skip Device Boot: 0x0 usb-storage: ATA 3 State Supsend: 0x0 usb-storage: Descriptor Override: 0x8 usb-storage: Last LUN Identifier: 0x0 usb-storage: SRST Enable: 0x0 usb-storage: Leaving isd200_read_config 00000000 usb-storage: isd200_action(ENUM,0xa0) usb-storage: Bulk command S 0x43425355 T 0x0 Trg 0 LUN 1 L 0 F 0 CL 0 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0010280 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Attempting to get CSW (2nd try)... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0010280 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Bulk status result = 2 usb-storage: isd200_action(0x04) error: 2 usb-storage: Setting Master/Slave selection to 0 usb-storage: Entering isd200_write_config usb-storage: Writing the following ISD200 Config Data: usb-storage: Event Notification: 0x0 usb-storage: External Clock: 0x0 usb-storage: ATA Init Timeout: 0x19 usb-storage: ATAPI Command Block Size: 0x0 usb-storage: Master/Slave Selection: 0x0 usb-storage: ATAPI Reset: 0x0 usb-storage: ATA Timing: 0x1 usb-storage: ATA Major Command: 0x24 usb-storage: ATA Minor Command: 0x24 usb-storage: Init Status: 0x0 usb-storage: Config Descriptor 2: 0x0 usb-storage: Skip Device Boot: 0x0 usb-storage: ATA 3 State Supsend: 0x0 usb-storage: Descriptor Override: 0x8 usb-storage: Last LUN Identifier: 0x0 usb-storage: SRST Enable: 0x0 usb-storage: usb_stor_ctrl_transfer(): rq=01 rqtype=40 value=0000 index=02 len=8 usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: ISD200 Config Data was written successfully usb-storage: Leaving isd200_write_config 00000000 usb-storage: Leaving isd200_manual_enum 00000000 usb-storage: Protocol changed to: Transparent SCSI usb-storage: Leaving isd200_get_inquiry_data 00000000 usb-storage: ISD200 Initialization complete usb-storage: *** thread sleeping. scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 36 F 128 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code -32; transferred 31/31 usb-storage: clearing endpoint halt for pipe 0xc0008200 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Bulk command transfer result=2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 0 F 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1 R 0 Stat 0x2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: device_reset() called usb-storage: Bulk reset requested usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 0 F 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1 R 0 Stat 0x2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: bus_reset() called drivers/usb/core/hub.c: USB device not accepting new address (error=-22) usb-storage: usb_reset_device returns -22 scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0 usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (1/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (2/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (3/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (4/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (5/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (6/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (7/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered.
--=_courier-8070-1048069329-0001-2--