linux-2.5.66-bk10 and bk9.
I got an oops with the hisax driver on initializing.
ksymoops 2.4.8 on i686 2.4.21-pre6. Options used
-v /home/mb/linux-2.5/linux-2.5.66-bk10/vmlinux (specified)
-K (specified)
-L (specified)
-O (specified)
-m /home/mb/linux-2.5/linux-2.5.66-bk10/System.map (specified)
Unable to handle kernel NULL pointer dereference at virtual address 00000004
c030bf8e
*pde = 00000000
Oops: 0000 [#1]
CPU: 0
EIP: 0060:[<c030bf8e>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010286
eax: 00000000 ebx: cfd0fc00 ecx: cfd12000 edx: cfd0fde0
esi: cfd12000 edi: cfd1210c ebp: c1293de0 esp: c1293dd0
ds: 007b es: 007b ss: 0068
Stack: cfd0fc00 cfd0fc2c cfd0fc00 cfd12000 c1293e10 c0317945 cfd0fc00 cfd12000
cfd1210c cfd1210c cfd12000 c1293e10 c0317858 cfd12124 cfd1210c cfd12000
c1293e2c c0317b74 cfd1210c cfd1213c cfd12000 c1293e9e cfd120da c1293e48
Call Trace:
[<c0317945>] init_d_st+0x52/0x11d
[<c0317858>] init_PStack+0x20/0xbb
[<c0317b74>] init_chan+0x10b/0x115
[<c0317ba4>] CallcNewChan+0x26/0xbf
[<c0309e67>] hisax_register+0x86/0x12b
[<c021024c>] pci_device_probe+0x5a/0x68
[<c02756a1>] bus_match+0x43/0x6e
[<c02757a2>] driver_attach+0x5d/0x6f
[<c0275abe>] bus_add_driver+0xe9/0xeb
[<c0275ed8>] driver_register+0x3a/0x3e
[<c0210363>] pci_register_driver+0x49/0x59
[<c01291ee>] init_workqueues+0x12/0x2c
[<c01050a3>] init+0x39/0x196
[<c010506a>] init+0x0/0x196
[<c0107289>] kernel_thread_helper+0x5/0xb
Code: 8b 50 04 85 d2 75 0a 8b 5d f8 8b 75 fc 89 ec 5d c3 89 74 24
>>EIP; c030bf8e <setstack_HiSax+85/a2> <=====
>>ebx; cfd0fc00 <_end+f792e48/3fa8304c>
>>ecx; cfd12000 <_end+f795248/3fa8304c>
>>edx; cfd0fde0 <_end+f793028/3fa8304c>
>>esi; cfd12000 <_end+f795248/3fa8304c>
>>edi; cfd1210c <_end+f795354/3fa8304c>
>>ebp; c1293de0 <_end+d17028/3fa8304c>
>>esp; c1293dd0 <_end+d17018/3fa8304c>
Trace; c0317945 <init_d_st+52/11d>
Trace; c0317858 <init_PStack+20/bb>
Trace; c0317b74 <init_chan+10b/115>
Trace; c0317ba4 <CallcNewChan+26/bf>
Trace; c0309e67 <hisax_register+86/12b>
Trace; c021024c <pci_device_probe+5a/68>
Trace; c02756a1 <bus_match+43/6e>
Trace; c02757a2 <driver_attach+5d/6f>
Trace; c0275abe <bus_add_driver+e9/eb>
Trace; c0275ed8 <driver_register+3a/3e>
Trace; c0210363 <pci_register_driver+49/59>
Trace; c01291ee <init_workqueues+12/2c>
Trace; c01050a3 <init+39/196>
Trace; c010506a <init+0/196>
Trace; c0107289 <kernel_thread_helper+5/b>
Code; c030bf8e <setstack_HiSax+85/a2>
00000000 <_EIP>:
Code; c030bf8e <setstack_HiSax+85/a2> <=====
0: 8b 50 04 mov 0x4(%eax),%edx <=====
Code; c030bf91 <setstack_HiSax+88/a2>
3: 85 d2 test %edx,%edx
Code; c030bf93 <setstack_HiSax+8a/a2>
5: 75 0a jne 11 <_EIP+0x11>
Code; c030bf95 <setstack_HiSax+8c/a2>
7: 8b 5d f8 mov 0xfffffff8(%ebp),%ebx
Code; c030bf98 <setstack_HiSax+8f/a2>
a: 8b 75 fc mov 0xfffffffc(%ebp),%esi
Code; c030bf9b <setstack_HiSax+92/a2>
d: 89 ec mov %ebp,%esp
Code; c030bf9d <setstack_HiSax+94/a2>
f: 5d pop %ebp
Code; c030bf9e <setstack_HiSax+95/a2>
10: c3 ret
Code; c030bf9f <setstack_HiSax+96/a2>
11: 89 74 24 00 mov %esi,0x0(%esp,1)
I traced tty with a serial line:
Linux version 2.5.66-bk10 (mb@lfs) (gcc version 3.2.2) #2 Sam Apr 5 16:13:53 CEST 2003
Video mode to be used for restore is 30b
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
user-defined physical RAM map:
user: 0000000000000000 - 000000000009fc00 (usable)
user: 000000000009fc00 - 00000000000a0000 (reserved)
user: 00000000000d0000 - 00000000000d4000 (reserved)
user: 00000000000f0000 - 0000000000100000 (reserved)
user: 0000000000100000 - 000000000fff0000 (usable)
user: 000000000fff0000 - 000000000fff8000 (ACPI data)
user: 000000000fff8000 - 0000000010000000 (ACPI NVS)
user: 00000000fec00000 - 00000000fec01000 (reserved)
user: 00000000fee00000 - 00000000fee01000 (reserved)
user: 00000000ffb00000 - 00000000ffc00000 (reserved)
user: 00000000fff00000 - 0000000100000000 (reserved)
255MB LOWMEM available.
found SMP MP-table at 000fb800
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 AMI ) @ 0x000fa300
ACPI: RSDT (v001 AMIINT INTEL845 00000.00016) @ 0x0fff0000
ACPI: FADT (v001 AMIINT INTEL845 00000.00017) @ 0x0fff0030
ACPI: MADT (v001 AMIINT INTEL845 00000.00009) @ 0x0fff00c0
ACPI: DSDT (v001 INTEL BROKDALE 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: console=ttyS1,9600 console=tty0 root=/dev/md0 hdd=ide-scsi hdb=ide-scsi mce vga=779 mem=262080K
ide_setup: hdd=ide-scsi
ide_setup: hdb=ide-scsi
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 2239.543 MHz processor.
Console: colour VGA+ 132x50
Calibrating delay loop... 4423.68 BogoMIPS
Memory: 254120k/262080k available (2908k kernel code, 7240k reserved, 1002k data, 352k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
-> /dev
-> /dev/console
-> /root
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
Machine check exception polling timer started.
CPU: Intel(R) Pentium(R) 4 CPU 1.60GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=0
testing the IO APIC.......................
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2239.0688 MHz.
..... host bus clock speed is 139.0980 MHz.
Initializing RT netlink socket
mtrr: v2.0 (20020519)
PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=3
PCI: Using configuration type 1
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
ACPI: Subsystem revision 20030328
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:....................................................................................................................................................
Table [DSDT] - 495 Objects with 44 Devices 148 Methods 15 Regions
ACPI Namespace successfully loaded at root c05414dc
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0731 [06] ev_create_gpe_block : GPE Block: [_GPE] 2 registers at 0000000000000828 on interrupt 9
evgpeblk-0736 [06] ev_create_gpe_block : GPE Block defined as GPE 0x00 to GPE 0x0F
evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L0B as GPE number 0x0B
evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L03 as GPE number 0x03
evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L04 as GPE number 0x04
evgpeblk-0731 [06] ev_create_gpe_block : GPE Block: [_GPE] 2 registers at 000000000000082C on interrupt 9
evgpeblk-0736 [06] ev_create_gpe_block : GPE Block defined as GPE 0x10 to GPE 0x1F
evgpeblk-0262 [07] ev_save_method_info : Registered GPE method _L1C as GPE number 0x1C
Executing all Device _STA and_INI methods:............................................
44 Devices found containing: 44 _STA, 1 _INI methods
Completing Region/Field/Buffer/Package initialization:..................................................................................
Initialized 10/15 Regions 10/10 Fields 50/50 Buffers 12/12 Packages (495 nodes)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
exfldio-0140 [25] ex_setup_region : Field [TOMR] Base+Offset+Width 0+2+1 is beyond end of region [TMEM] (length 2)
dswexec-0421 [17] ds_exec_end_op : [ShiftLeft]: Could not resolve operands, AE_AML_REGION_LIMIT
psparse-1121: *** Error: Method execution failed [\_SB_.PCI0.MDET] (Node c12d88a8), AE_AML_REGION_LIMIT
psparse-1121: *** Error: Method execution failed [\_SB_.PCI0._CRS] (Node c12d8e28), AE_AML_REGION_LIMIT
uteval-0098: *** Error: Method execution failed [\_SB_.PCI0._CRS] (Node c12d8e28), AE_AML_REGION_LIMIT
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Br
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.95 (c) Adam Belay
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7520
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x65ab, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 15
exit congestion at 17
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
Enabling SEP on CPU 0
Total HugeTLB memory allocated, 0
Journalled Block Device driver loaded
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
pty: 256 Unix98 ptys configured
lp: driver loaded but no devices found
Real Time Clock Driver v1.11
Non-volatile memory driver v1.2
Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Intel i845 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
eth0: RealTek RTL-8029 found at 0xb400, IRQ 17, 52:54:05:FF:F5:EA.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux video capture interface: v1.00
bttv: driver version 0.9.4 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Host bridge is Intel Corp. 82845 845 (Brookdale
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 03:02.0, irq: 18, latency: 32, mmio: 0xddafe000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=44354, tuner=Philips FM1216 (5), radio=yes
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
msp34xx: init: chip=MSP3415D-B3, has NICAM support
msp3410: daemon started
bttv0: i2c attach [client=MSP3415D-B3,ok]
registering 0-0040
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951)
tuner: probing bt848 #0 i2c adapter [id=0x10005]
tuner: chip found @ 0xc2
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: i2c attach [client=Philips PAL_BG (FI1216 and compatibles),ok]
registering 0-0061
tda9887: probing bt848 #0 i2c adapter [id=0x10005]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L040AVVA07-0, ATA DISK drive
hdb: LG DVD-ROM DRD-8160B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: IC35L040AVVA07-0, ATA DISK drive
hdd: CD-W54E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=79780/16/63, UDMA(100)
hda: hda1 hda2 hda3 < hda5 hda6 >
hdc: host protected area => 1
hdc: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=79780/16/63, UDMA(33)
hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 hdc7 >
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LG Model: DVD-ROM DRD8160B Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TEAC Model: CD-W54E Rev: 1.0Y
Type: CD-ROM ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
mice: PS/2 mouse device common for all mice
input: PC Speaker
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
I2O Core - (C) Copyright 1999 Red Hat Software
I2O: Event thread created as pid 12
i2o: Checking for PCI I2O controllers...
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
I2O Block Storage OSM v0.9
(c) Copyright 1999-2001 Red Hat Software.
i2o_block: Checking for Boot device...
i2o_block: Checking for I2O Block devices...
i2o_scsi.c: Version 0.1.2
chain_pool: 0 bytes @ cfdc66a0
(512 byte buffers X 4 can_queue X 0 i2o controllers)
i2c-dev.o: i2c /dev entries driver module version 2.7.0 (20021208)
md: raid0 personality registered as nr 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
ISDN subsystem initialized
PPP BSD Compression module registered
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (kernel)
HiSax: Layer1 Revision 2.41.6.5
HiSax: Layer2 Revision 2.25.6.4
HiSax: TeiMgr Revision 2.17.6.3
HiSax: Layer3 Revision 2.17.6.5
HiSax: LinkLayer Revision 2.51.6.6
HiSax: Approval certification failed because of
HiSax: unauthorized source code changes
hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
get_drv 0: 0 -> 1
HiSax: Card 1 Protocol EDSS1 Id=fcpcipnp0 (0)
Unable to handle kernel NULL pointer dereference at virtual address 00000004
printing eip:
c030bf8e
*pde = 00000000
Oops: 0000 [#1]
CPU: 0
EIP: 0060:[<c030bf8e>] Not tainted
EFLAGS: 00010286
EIP is at setstack_HiSax+0x85/0xa2
eax: 00000000 ebx: cfd0fc00 ecx: cfd12000 edx: cfd0fde0
esi: cfd12000 edi: cfd1210c ebp: c1293de0 esp: c1293dd0
ds: 007b es: 007b ss: 0068
Process swapper (pid: 1, threadinfo=c1292000 task=c12ae080)
Stack: cfd0fc00 cfd0fc2c cfd0fc00 cfd12000 c1293e10 c0317945 cfd0fc00 cfd12000
cfd1210c cfd1210c cfd12000 c1293e10 c0317858 cfd12124 cfd1210c cfd12000
c1293e2c c0317b74 cfd1210c cfd1213c cfd12000 c1293e9e cfd120da c1293e48
Call Trace:
[<c0317945>] init_d_st+0x52/0x11d
[<c0317858>] init_PStack+0x20/0xbb
[<c0317b74>] init_chan+0x10b/0x115
[<c0317ba4>] CallcNewChan+0x26/0xbf
[<c0309e67>] hisax_register+0x86/0x12b
[<c021024c>] pci_device_probe+0x5a/0x68
[<c02756a1>] bus_match+0x43/0x6e
[<c02757a2>] driver_attach+0x5d/0x6f
[<c0275abe>] bus_add_driver+0xe9/0xeb
[<c0275ed8>] driver_register+0x3a/0x3e
[<c0210363>] pci_register_driver+0x49/0x59
[<c01291ee>] init_workqueues+0x12/0x2c
[<c01050a3>] init+0x39/0x196
[<c010506a>] init+0x0/0x196
[<c0107289>] kernel_thread_helper+0x5/0xb
Code: 8b 50 04 85 d2 75 0a 8b 5d f8 8b 75 fc 89 ec 5d c3 89 74 24
<0>Kernel panic: Attempted to kill init!
.config (grep "=[y|m]" .config)
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_EXPERIMENTAL=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSCTL=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_KMOD=y
CONFIG_X86_PC=y
CONFIG_MPENTIUM4=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_PREFETCH=y
CONFIG_X86_SSE2=y
CONFIG_HUGETLB_PAGE=y
CONFIG_PREEMPT=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PM=y
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
CONFIG_KCORE_ELF=y
CONFIG_BINFMT_ELF=y
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
CONFIG_PARPORT_1284=y
CONFIG_PNP=y
CONFIG_PNP_NAMES=y
CONFIG_PNPBIOS=y
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_IDEDMA_AUTO=y
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=y
CONFIG_CHR_DEV_SG=y
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_RAID0=y
CONFIG_I2O=y
CONFIG_I2O_PCI=y
CONFIG_I2O_BLOCK=y
CONFIG_I2O_SCSI=y
CONFIG_I2O_PROC=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_NETFILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_NET_IPGRE=y
CONFIG_SYN_COOKIES=y
CONFIG_IP_NF_CONNTRACK=y
CONFIG_IP_NF_FTP=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TCPMSS=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_UNCLEAN=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_MIRROR=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_NAT_FTP=y
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IPV6_SCTP__=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_NET_PCI=y
CONFIG_NE2K_PCI=y
CONFIG_PPP=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPP_BSDCOMP=y
CONFIG_PPPOE=y
CONFIG_SLIP=y
CONFIG_SLIP_COMPRESSED=y
# Token Ring devices (depends on LLC=y)
CONFIG_ISDN_BOOL=y
CONFIG_ISDN=y
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_PPP_BSDCOMP=y
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
CONFIG_ISDN_DRV_HISAX=y
CONFIG_HISAX_EURO=y
CONFIG_HISAX_FRITZ_PCIPNP=y
CONFIG_INPUT=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_PRINTER=y
CONFIG_I2C=y
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_CHARDEV=y
CONFIG_SENSORS_W83781D=y
CONFIG_I2C_SENSOR=y
CONFIG_WATCHDOG=y
CONFIG_SOFT_WATCHDOG=y
CONFIG_NVRAM=y
CONFIG_RTC=y
CONFIG_AGP=y
CONFIG_AGP_INTEL=y
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_PROC_FS=y
CONFIG_VIDEO_BT848=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V4=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_ISO8859_15=y
CONFIG_VIDEO_SELECT=y
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_ENS1371=y
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_KALLSYMS=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_FRAME_POINTER=y
CONFIG_X86_EXTRA_IRQS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_AES=y
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_X86_BIOS_REBOOT=y
Regards Michael Buesch.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/