Ok, here are the requested infos:
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.29
South Bridge: VIA vt82c686a
Revision: ISA 0x14 IDE 0x6
Highest DMA rate: UDMA66
BM-DMA base: 0xffa0
PCI clock: 33MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: no yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: PIO PIO UDMA UDMA
Address Setup: 120ns 120ns 30ns 30ns
Cmd Active: 480ns 480ns 90ns 90ns
Cmd Recovery: 480ns 480ns 30ns 30ns
Data Active: 330ns 330ns 90ns 90ns
Data Recovery: 270ns 270ns 30ns 30ns
Cycle Time: 600ns 600ns 45ns 60ns
Transfer Rate: 3.3MB/s 3.3MB/s 44.0MB/s 33.0MB/s
/dev/hdc:
Model=WDC WD136AA, FwRev=80.10A80, SerialNo=WD-WM6780207230
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs
FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=26564832
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4
/dev/hdd:
Model=Pioneer DVD-ROM ATAPIModel DVD-104S 020, FwRev=E2.06, SerialNo=
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=13395, BuffSize=64kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4
As I mentioned, the bios recognizes my hd as an udma4 capable device, so
it's not a cable issue, I think, the driver won't detect properly the
cables. By the way, it would be good to have driver parameters, that
help setting the prefetch buffer and post write buffer on, because on
the secondary channel, it's off by default, I'm using powertweak to
enable them. Thx.
Paco
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/