Summary:
core modules (continued)
diffstat:
include/asm-i386/bugs.h | 2
include/asm-i386/dma.h | 7 +
include/asm-i386/io.h | 6 +
include/asm-i386/irq.h | 4
include/asm-i386/pc9800.h | 27 ++++
include/asm-i386/pc9800_debug.h | 152 +++++++++++++++++++++++++
include/asm-i386/pc9800_dma.h | 238 ++++++++++++++++++++++++++++++++++++++++
include/asm-i386/pc9800_sca.h | 25 ++++
include/asm-i386/pgtable.h | 4
include/asm-i386/processor.h | 2
include/asm-i386/scatterlist.h | 6 +
include/asm-i386/setup.h | 3
include/asm-i386/timex.h | 4
13 files changed, 479 insertions(+), 1 deletion(-)
patch:
diff -urN linux/include/asm-i386/bugs.h linux98/include/asm-i386/bugs.h
--- linux/include/asm-i386/bugs.h Sun Jun 9 14:27:38 2002
+++ linux98/include/asm-i386/bugs.h Mon Jun 10 20:49:15 2002
@@ -34,6 +34,7 @@
__setup("no-hlt", no_halt);
+#ifndef CONFIG_PC9800
static int __init mca_pentium(char *s)
{
mca_pentium_flag = 1;
@@ -41,6 +42,7 @@
}
__setup("mca-pentium", mca_pentium);
+#endif
static int __init no_387(char *s)
{
diff -urN linux/include/asm-i386/dma.h linux98/include/asm-i386/dma.h
--- linux/include/asm-i386/dma.h Sat Jul 21 04:52:59 2001
+++ linux98/include/asm-i386/dma.h Fri Aug 17 22:15:06 2001
@@ -10,6 +10,9 @@
#include <linux/config.h>
#include <linux/spinlock.h> /* And spinlocks */
+#ifdef CONFIG_PC9800
+#include <asm/pc9800_dma.h>
+#else /* !CONFIG_PC9800 */
#include <asm/io.h> /* need byte IO */
#include <linux/delay.h>
@@ -72,8 +75,10 @@
#define MAX_DMA_CHANNELS 8
+#ifndef CONFIG_PC9800
/* The maximum address that we can perform a DMA transfer to on this platform */
#define MAX_DMA_ADDRESS (PAGE_OFFSET+0x1000000)
+#endif
/* 8237 DMA controllers */
#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
@@ -295,4 +300,6 @@
#define isa_dma_bridge_buggy (0)
#endif
+#endif /* CONFIG_PC9800 */
+
#endif /* _ASM_DMA_H */
diff -urN linux/include/asm-i386/io.h linux98/include/asm-i386/io.h
--- linux/include/asm-i386/io.h Sat Oct 12 13:22:45 2002
+++ linux98/include/asm-i386/io.h Sat Oct 12 19:25:19 2002
@@ -27,6 +27,8 @@
* Linus
*/
+#include <linux/config.h>
+
/*
* Bit simplified and optimized by Jan Hubicka
* Support of BIGMEM added by Gerhard Wichert, Siemens AG, July 1999.
@@ -288,7 +290,11 @@
#ifdef SLOW_IO_BY_JUMPING
#define __SLOW_DOWN_IO "jmp 1f; 1: jmp 1f; 1:"
#else
+#ifndef CONFIG_PC9800
#define __SLOW_DOWN_IO "outb %%al,$0x80;"
+#else
+#define __SLOW_DOWN_IO "outb %%al,$0x5f;"
+#endif
#endif
static inline void slow_down_io(void) {
diff -urN linux/include/asm-i386/irq.h linux98/include/asm-i386/irq.h
--- linux/include/asm-i386/irq.h Sat Sep 21 00:20:16 2002
+++ linux98/include/asm-i386/irq.h Sat Sep 21 07:17:56 2002
@@ -17,7 +17,11 @@
static __inline__ int irq_cannonicalize(int irq)
{
+#ifndef CONFIG_PC9800
return ((irq == 2) ? 9 : irq);
+#else
+ return ((irq == 7) ? 11 : irq);
+#endif
}
extern void disable_irq(unsigned int);
diff -urN linux/include/asm-i386/pc9800.h linux98/include/asm-i386/pc9800.h
--- linux/include/asm-i386/pc9800.h Thu Jan 1 09:00:00 1970
+++ linux98/include/asm-i386/pc9800.h Fri Aug 17 21:50:18 2001
@@ -0,0 +1,27 @@
+/*
+ * PC-9800 machine types.
+ *
+ * Copyright (C) 1999 TAKAI Kosuke <tak@kmc.kyoto-u.ac.jp>
+ * (Linux/98 Project)
+ */
+
+#ifndef _ASM_PC9800_H_
+#define _ASM_PC9800_H_
+
+#include <asm/pc9800_sca.h>
+#include <asm/types.h>
+
+#define __PC9800SCA(type, pa) (*(type *) phys_to_virt(pa))
+#define __PC9800SCA_TEST_BIT(pa, n) \
+ ((__PC9800SCA(u8, pa) & (1U << (n))) != 0)
+
+#define PC9800_HIGHRESO_P() __PC9800SCA_TEST_BIT(PC9800SCA_BIOS_FLAG, 3)
+#define PC9800_8MHz_P() __PC9800SCA_TEST_BIT(PC9800SCA_BIOS_FLAG, 7)
+
+ /* 0x2198 is 98 21 on memory... */
+#define PC9800_9821_P() (__PC9800SCA(u16, PC9821SCA_ROM_ID) == 0x2198)
+
+/* Note PC9821_...() are valid only when PC9800_9821_P() was true. */
+#define PC9821_IDEIF_DOUBLE_P() __PC9800SCA_TEST_BIT(PC9821SCA_ROM_FLAG4, 4)
+
+#endif
diff -urN linux/include/asm-i386/pc9800_debug.h linux98/include/asm-i386/pc9800_debug.h
--- linux/include/asm-i386/pc9800_debug.h Thu Jan 1 09:00:00 1970
+++ linux98/include/asm-i386/pc9800_debug.h Fri Aug 17 22:20:21 2001
@@ -0,0 +1,152 @@
+/*
+ * linux/include/asm-i386/pc9800_debug.h: Defines for debug routines
+ *
+ * Written by Linux/98 Project, 1998.
+ *
+ * Revised by TAKAI Kousuke, Nov 1999.
+ */
+
+#ifndef _ASM_PC9800_DEBUG_H
+#define _ASM_PC9800_DEBUG_H
+
+extern unsigned char __pc9800_beep_flag;
+
+/* Don't depend on <asm/io.h> ... */
+static __inline__ void pc9800_beep_on(void)
+{
+ __asm__ ("out%B0 %0,%1" : : "a"((char) 0x6), "N"(0x37));
+ __pc9800_beep_flag = 0x6;
+}
+
+static __inline__ void pc9800_beep_off(void)
+{
+ __asm__ ("out%B0 %0,%1" : : "a"((char) 0x7), "N"(0x37));
+ __pc9800_beep_flag = 0x7;
+}
+
+static __inline__ void pc9800_beep_toggle(void)
+{
+ __pc9800_beep_flag ^= 1;
+ __asm__ ("out%B0 %0,%1" : : "a"(__pc9800_beep_flag), "N"(0x37));
+}
+
+static __inline__ void pc9800_udelay(unsigned int __usec)
+{
+ if ((__usec = __usec * 10 / 6) > 0)
+ do
+ __asm__ ("out%B0 %%al,%0" : : "N"(0x5F));
+ while (--__usec);
+}
+
+# define assertk(expr) ({ \
+ if (!(expr)) { \
+ __pc9800_saveregs(); \
+ __assert_fail(__BASE_FILE__, __FILE__, __LINE__, \
+ __PRETTY_FUNCTION__, \
+ __builtin_return_address (0), #expr); \
+ } \
+})
+# define check_kernel_pointer(expr) ({ \
+ void *__p = (expr); \
+ if ((unsigned long) __p < PAGE_OFFSET) { \
+ __pc9800_saveregs(); \
+ __invalid_kernel_pointer \
+ (__BASE_FILE__, __FILE__, __LINE__, \
+ __PRETTY_FUNCTION__, \
+ __builtin_return_address(0), #expr, __p); \
+ } \
+})
+
+extern void __assert_fail(const char *, const char *, unsigned int,
+ const char *, void *, const char *)
+ __attribute__ ((__noreturn__));
+extern void __invalid_kernel_pointer(const char *, const char *, unsigned int,
+ const char *, void *,
+ const char *, void *)
+ __attribute__ ((__noreturn__));
+extern void __pc9800_saveregs(void);
+
+extern void ucg_saveargs(unsigned int, ...);
+
+#ifdef NEED_UNMAP_PHYSPAGE
+
+#include <linux/mm.h>
+#include <asm/pgtable.h>
+#include <asm/pgalloc.h>
+
+/*
+ * unmap_physpage (addr)
+ */
+static __inline__ void
+unmap_physpage(unsigned long addr)
+{
+ pgd_t *pgd = pgd_offset_k(addr);
+ pmd_t *pmd;
+ pte_t *pte;
+
+ if (pgd_none(*pgd))
+ panic("%s: No pgd?!?", __BASE_FILE__);
+ pmd = pmd_offset(pgd, addr);
+ if (pmd_none(*pmd))
+ panic("%s: No pmd?!?", __BASE_FILE__);
+ if (pmd_val(*pmd) & _PAGE_PSE) {
+ int i;
+ unsigned long paddr = pmd_val(*pmd) & PAGE_MASK;
+
+ pte = (pte_t *) __get_free_page(GFP_KERNEL);
+ set_pmd(pmd, __pmd(_KERNPG_TABLE + __pa(pte)));
+ for (i = 0; i < PTRS_PER_PTE; pte++, i++)
+ *pte = mk_pte_phys(paddr + i * PAGE_SIZE,
+ PAGE_KERNEL);
+ }
+ pte = pte_offset(pmd, addr);
+
+ set_pte(pte, pte_modify(*pte, PAGE_NONE));
+ __flush_tlb_one(addr);
+}
+#endif /* NEED_UNMAP_PHYSPAGE */
+
+#ifdef NEED_KERNEL_POINTER_CHECKER
+# /* no dep */ include <asm/uaccess.h>
+
+/*
+ * KERNEL_POINTER_VALIDP(PTR) validates kernel pointer PTR.
+ * If PTR points vaild memory address for kernel internal use,
+ * return nonzero; otherwise return zero.
+ *
+ * Note PTR is invalid if PTR points user area.
+ */
+#define KERNEL_POINTER_VALIDP(PTR) ({ \
+ const int *_ptr = (const int *) (PTR); \
+ int _dummy; \
+ (unsigned long) _ptr >= PAGE_OFFSET \
+ && !__get_user(_dummy, _ptr); \
+})
+
+/*
+ * Similar, but validates for a trivial string in kernel.
+ * Here `trivial' means that the string has no non-ASCII characters
+ * and is shorter than 80 characters.
+ *
+ * Note this is intended for checking various `name' (I/O
+ * resources and so on).
+ */
+#define KERNEL_POINTER_TRIVIAL_STRING_P(PTR) ({ \
+ const char *_ptr = (const char *) (PTR); \
+ char _dummy; \
+ (unsigned long) _ptr >= PAGE_OFFSET \
+ && ({ int _result; \
+ while (!(_result = __get_user(_dummy, _ptr)) \
+ && _dummy) \
+ _ptr++; \
+ !_result; }); })
+
+#endif /* NEED_VALIDATE_KERNEL_POINTER */
+
+#endif /* _ASM_PC9800_DEBUG_H */
+
+/*
+ * Local variables:
+ * c-file-style: "linux"
+ * End:
+ */
diff -urN linux/include/asm-i386/pc9800_dma.h linux98/include/asm-i386/pc9800_dma.h
--- linux/include/asm-i386/pc9800_dma.h Thu Jan 1 09:00:00 1970
+++ linux98/include/asm-i386/pc9800_dma.h Fri Aug 17 22:15:01 2001
@@ -0,0 +1,238 @@
+/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
+ * linux/include/asm/dma.h: Defines for using and allocating dma channels.
+ * Written by Hennus Bergman, 1992.
+ * High DMA channel support & info by Hannu Savolainen
+ * and John Boyd, Nov. 1992.
+ */
+
+#ifndef _ASM_PC9800_DMA_H
+#define _ASM_PC9800_DMA_H
+
+#include <linux/config.h>
+#include <asm/io.h> /* need byte IO */
+#include <linux/delay.h>
+
+
+#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
+#define dma_outb outb_p
+#else
+#define dma_outb outb
+#endif
+
+#define dma_inb inb
+
+/*
+ * NOTES about DMA transfers:
+ *
+ * controller 1: channels 0-3, byte operations, ports 00-1F
+ * controller 2: channels 4-7, word operations, ports C0-DF
+ *
+ * - ALL registers are 8 bits only, regardless of transfer size
+ * - channel 4 is not used - cascades 1 into 2.
+ * - channels 0-3 are byte - addresses/counts are for physical bytes
+ * - channels 5-7 are word - addresses/counts are for physical words
+ * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
+ * - transfer count loaded to registers is 1 less than actual count
+ * - controller 2 offsets are all even (2x offsets for controller 1)
+ * - page registers for 5-7 don't use data bit 0, represent 128K pages
+ * - page registers for 0-3 use bit 0, represent 64K pages
+ *
+ * DMA transfers are limited to the lower 16MB of _physical_ memory.
+ * Note that addresses loaded into registers must be _physical_ addresses,
+ * not logical addresses (which may differ if paging is active).
+ *
+ * Address mapping for channels 0-3:
+ *
+ * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
+ * | ... | | ... | | ... |
+ * | ... | | ... | | ... |
+ * | ... | | ... | | ... |
+ * P7 ... P0 A7 ... A0 A7 ... A0
+ * | Page | Addr MSB | Addr LSB | (DMA registers)
+ *
+ * Address mapping for channels 5-7:
+ *
+ * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
+ * | ... | \ \ ... \ \ \ ... \ \
+ * | ... | \ \ ... \ \ \ ... \ (not used)
+ * | ... | \ \ ... \ \ \ ... \
+ * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
+ * | Page | Addr MSB | Addr LSB | (DMA registers)
+ *
+ * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
+ * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
+ * the hardware level, so odd-byte transfers aren't possible).
+ *
+ * Transfer count (_not # bytes_) is limited to 64K, represented as actual
+ * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
+ * and up to 128K bytes may be transferred on channels 5-7 in one operation.
+ *
+ */
+
+#define MAX_DMA_CHANNELS 4
+
+/* The maximum address that we can perform a DMA transfer to on this platform */
+#define MAX_DMA_ADDRESS (~0UL)
+
+/* 8237 DMA controllers */
+#define IO_DMA_BASE 0x01
+
+/* DMA controller registers */
+#define DMA_CMD_REG ((IO_DMA_BASE)+0x10) /* command register (w) */
+#define DMA_STAT_REG ((IO_DMA_BASE)+0x10) /* status register (r) */
+#define DMA_REQ_REG ((IO_DMA_BASE)+0x12) /* request register (w) */
+#define DMA_MASK_REG ((IO_DMA_BASE)+0x14) /* single-channel mask (w) */
+#define DMA_MODE_REG ((IO_DMA_BASE)+0x16) /* mode register (w) */
+#define DMA_CLEAR_FF_REG ((IO_DMA_BASE)+0x18) /* clear pointer flip-flop (w) */
+#define DMA_TEMP_REG ((IO_DMA_BASE)+0x1A) /* Temporary Register (r) */
+#define DMA_RESET_REG ((IO_DMA_BASE)+0x1A) /* Master Clear (w) */
+#define DMA_CLR_MASK_REG ((IO_DMA_BASE)+0x1C) /* Clear Mask */
+#define DMA_MASK_ALL_REG ((IO_DMA_BASE)+0x1E) /* all-channels mask (w) */
+
+#define DMA_PAGE_0 0x27 /* DMA page registers */
+#define DMA_PAGE_1 0x21
+#define DMA_PAGE_2 0x23
+#define DMA_PAGE_3 0x25
+
+#define DMA_Ex_PAGE_0 0xe05 /* DMA Extended page reg base */
+#define DMA_Ex_PAGE_1 0xe07
+#define DMA_Ex_PAGE_2 0xe09
+#define DMA_Ex_PAGE_3 0xe0b
+
+#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
+#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
+#define DMA_AUTOINIT 0x10
+
+extern spinlock_t dma_spin_lock;
+
+static __inline__ unsigned long claim_dma_lock(void)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&dma_spin_lock, flags);
+ return flags;
+}
+
+static __inline__ void release_dma_lock(unsigned long flags)
+{
+ spin_unlock_irqrestore(&dma_spin_lock, flags);
+}
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+ dma_outb(dmanr, DMA_MASK_REG);
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+ dma_outb(dmanr | 4, DMA_MASK_REG);
+}
+
+/* Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while holding the DMA lock ! ---
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+ dma_outb(0, DMA_CLEAR_FF_REG);
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+ dma_outb(mode | dmanr, DMA_MODE_REG);
+}
+
+/* Set only the page register bits of the transfer address.
+ * This is used for successive transfers when we know the contents of
+ * the lower 16 bits of the DMA current address register, but a 64k boundary
+ * may have been crossed.
+ */
+static __inline__ void set_dma_page(unsigned int dmanr, unsigned int pagenr)
+{
+ unsigned char low=pagenr&0xff;
+ unsigned char hi=pagenr>>8;
+
+ switch(dmanr) {
+ case 0:
+ dma_outb(low, DMA_PAGE_0);
+ dma_outb(hi, DMA_Ex_PAGE_0);
+ break;
+ case 1:
+ dma_outb(low, DMA_PAGE_1);
+ dma_outb(hi, DMA_Ex_PAGE_1);
+ break;
+ case 2:
+ dma_outb(low, DMA_PAGE_2);
+ dma_outb(hi, DMA_Ex_PAGE_2);
+ break;
+ case 3:
+ dma_outb(low, DMA_PAGE_3);
+ dma_outb(hi, DMA_Ex_PAGE_3);
+ break;
+ }
+}
+
+/* Set transfer address & page bits for specific DMA channel.
+ * Assumes dma flipflop is clear.
+ */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+ set_dma_page(dmanr, a>>16);
+ dma_outb( a & 0xff, ((dmanr&3)<<2) + IO_DMA_BASE );
+ dma_outb( (a>>8) & 0xff, ((dmanr&3)<<2) + IO_DMA_BASE );
+}
+
+
+/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
+ * a specific DMA channel.
+ * You must ensure the parameters are valid.
+ * NOTE: from a manual: "the number of transfers is one more
+ * than the initial word count"! This is taken into account.
+ * Assumes dma flip-flop is clear.
+ * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+ count--;
+ dma_outb( count & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA_BASE );
+ dma_outb( (count>>8) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA_BASE );
+}
+
+
+/* Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * If called before the channel has been used, it may return 1.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ *
+ * Assumes DMA flip-flop is clear.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+ /* using short to get 16-bit wrap around */
+ unsigned short count;
+
+ count = 1 + dma_inb(((dmanr&3)<<2) + 2 + IO_DMA_BASE);
+ count += dma_inb(((dmanr&3)<<2) + 2 + IO_DMA_BASE) << 8;
+
+ return count;
+}
+
+
+/* These are in kernel/dma.c: */
+extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr); /* release it again */
+
+/* From PCI */
+
+#ifdef CONFIG_PCI
+extern int isa_dma_bridge_buggy;
+#else
+#define isa_dma_bridge_buggy (0)
+#endif
+
+#endif /* _ASM_PC9800_DMA_H */
diff -urN linux/include/asm-i386/pc9800_sca.h linux98/include/asm-i386/pc9800_sca.h
--- linux/include/asm-i386/pc9800_sca.h Thu Jan 1 09:00:00 1970
+++ linux98/include/asm-i386/pc9800_sca.h Fri Aug 17 21:50:18 2001
@@ -0,0 +1,25 @@
+/*
+ * System-common area definitions for NEC PC-9800 series
+ *
+ * Copyright (C) 1999 TAKAI Kousuke <tak@kmc.kyoto-u.ac.jp>,
+ * Kyoto University Microcomputer Club.
+ */
+
+#ifndef _ASM_I386_PC9800SCA_H_
+#define _ASM_I386_PC9800SCA_H_
+
+#define PC9800SCA_EXPMMSZ (0x0401) /* B */
+#define PC9800SCA_SCSI_PARAMS (0x0460) /* 8 * 4B */
+#define PC9800SCA_DISK_EQUIPS (0x0482) /* B */
+#define PC9800SCA_XROM_ID (0x04C0) /* 52B */
+#define PC9800SCA_BIOS_FLAG (0x0501) /* B */
+#define PC9800SCA_MMSZ16M (0x0594) /* W */
+
+/* PC-9821 have additional system common area in their BIOS-ROM segment. */
+
+#define PC9821SCA__BASE (0xF8E8 << 4)
+#define PC9821SCA_ROM_ID (PC9821SCA__BASE + 0x00)
+#define PC9821SCA_ROM_FLAG4 (PC9821SCA__BASE + 0x05)
+#define PC9821SCA_RSFLAGS (PC9821SCA__BASE + 0x11) /* B */
+
+#endif /* !_ASM_I386_PC9800SCA_H_ */
diff -urN linux/include/asm-i386/pgtable.h linux98/include/asm-i386/pgtable.h
--- linux/include/asm-i386/pgtable.h Mon Apr 15 04:18:55 2002
+++ linux98/include/asm-i386/pgtable.h Wed Apr 17 10:37:22 2002
@@ -58,7 +58,11 @@
#endif
#endif
+#ifndef CONFIG_PC9800
#define __beep() asm("movb $0x3,%al; outb %al,$0x61")
+#else
+#define __beep() asm("movb $0x6,%al; outb %al,$0x37")
+#endif
#define PMD_SIZE (1UL << PMD_SHIFT)
#define PMD_MASK (~(PMD_SIZE-1))
diff -urN linux/include/asm-i386/processor.h linux98/include/asm-i386/processor.h
--- linux/include/asm-i386/processor.h Sat Sep 21 00:20:15 2002
+++ linux98/include/asm-i386/processor.h Sun Sep 22 09:16:38 2002
@@ -87,7 +87,7 @@
#define current_cpu_data boot_cpu_data
#endif
-extern char ignore_irq13;
+extern char ignore_fpu_irq;
extern void identify_cpu(struct cpuinfo_x86 *);
extern void print_cpu_info(struct cpuinfo_x86 *);
diff -urN linux/include/asm-i386/scatterlist.h linux98/include/asm-i386/scatterlist.h
--- linux/include/asm-i386/scatterlist.h Mon Apr 15 04:18:52 2002
+++ linux98/include/asm-i386/scatterlist.h Wed Apr 17 10:37:22 2002
@@ -1,6 +1,8 @@
#ifndef _I386_SCATTERLIST_H
#define _I386_SCATTERLIST_H
+#include <linux/config.h>
+
struct scatterlist {
struct page *page;
unsigned int offset;
@@ -8,6 +10,10 @@
unsigned int length;
};
+#ifdef CONFIG_PC9800
+#define ISA_DMA_THRESHOLD (0xffffffff)
+#else
#define ISA_DMA_THRESHOLD (0x00ffffff)
+#endif
#endif /* !(_I386_SCATTERLIST_H) */
diff -urN linux/include/asm-i386/setup.h linux98/include/asm-i386/setup.h
--- linux/include/asm-i386/setup.h Tue Sep 10 02:35:13 2002
+++ linux98/include/asm-i386/setup.h Tue Sep 10 09:34:57 2002
@@ -28,6 +28,9 @@
#define APM_BIOS_INFO (*(struct apm_bios_info *) (PARAM+0x40))
#define DRIVE_INFO (*(struct drive_info_struct *) (PARAM+0x80))
#define SYS_DESC_TABLE (*(struct sys_desc_table_struct*)(PARAM+0xa0))
+#ifdef CONFIG_PC9800
+#define PC9800_MISC_FLAGS (*(unsigned char *)(PARAM+0x1AF))
+#endif
#define MOUNT_ROOT_RDONLY (*(unsigned short *) (PARAM+0x1F2))
#define RAMDISK_FLAGS (*(unsigned short *) (PARAM+0x1F8))
#define VIDEO_MODE (*(unsigned short *) (PARAM+0x1FA))
diff -urN linux/include/asm-i386/timex.h linux98/include/asm-i386/timex.h
--- linux/include/asm-i386/timex.h Thu Feb 14 18:09:15 2002
+++ linux98/include/asm-i386/timex.h Thu Feb 14 23:58:57 2002
@@ -9,11 +9,15 @@
#include <linux/config.h>
#include <asm/msr.h>
+#ifdef CONFIG_PC9800
+ extern int CLOCK_TICK_RATE;
+#else
#ifdef CONFIG_MELAN
# define CLOCK_TICK_RATE 1189200 /* AMD Elan has different frequency! */
#else
# define CLOCK_TICK_RATE 1193180 /* Underlying HZ */
#endif
+#endif
#define CLOCK_TICK_FACTOR 20 /* Factor of both 1000000 and CLOCK_TICK_RATE */
#define FINETUNE ((((((long)LATCH * HZ - CLOCK_TICK_RATE) << SHIFT_HZ) * \
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/