Tied it (2.4.21pre3-ac4) and still not working.
Regards Simon
> -Tupshin
>
> Simon Posnjak wrote:
>
> >Hi all,
> >
> >I have a Kudoz 7x board (VIA KT400 (VT8377 and VT8235)) and a WD 80 GB
> >disk (7200, UDMA (http://www.wdc.com/products/Products.asp?DriveID=32)).
> >
> >The problem is that disk operations are rally slow. Copying files goes
> >on with 1 MB/sec.
> >
> >At start up kernel complained:
> >
> >VP_IDE: IDE controller on PCI bus 00 dev 89
> >PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=biosirq.
> >VP_IDE: chipset revision 6
> >
> >So I added pci=biosirq to kernel parameters at boot. An then I got:
> >
> >Uniform Multi-Platform E-IDE driver Revision: 6.31
> >ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> >VP_IDE: IDE controller on PCI bus 00 dev 89
> >PCI: No IRQ known for interrupt pin A of device 00:11.1.
> >VP_IDE: chipset revision 6
> >VP_IDE: not 100% native mode: will probe irqs later
> >VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
> > ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:DMA, hdb:pio
> > ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:DMA, hdd:DMA
> >hda: WDC WD800JB-00CRA1, ATA DISK drive
> >hdc: SAMSUNG CD-R/RW SW-216B BS05 20010727, ATAPI CD/DVD-ROM drive
> >hdd: SAMSUNG CD-ROM SC-152L, ATAPI CD/DVD-ROM drive
> >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >ide1 at 0x170-0x177,0x376 on irq 15
> >hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=9729/255/63, UDMA(100)
> >
> >hdparm says:
> >
> >/dev/hda:
> > multcount = 16 (on)
> > IO_support = 1 (32-bit)
> > unmaskirq = 1 (on)
> > using_dma = 1 (on)
> > keepsettings = 0 (off)
> > readonly = 0 (off)
> > readahead = 8 (on)
> > geometry = 9729/255/63, sectors = 156301488, start = 0
> >
> >hdparm -iI /dev/hda
> >
> >/dev/hda:
> >
> > Model=WDC WD800JB-00CRA1, FwRev=17.07W17, SerialNo=WD-WCA8E5325146
> > Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
> > RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
> > BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
> > CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
> > IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> > PIO modes: pio0 pio1 pio2 pio3 pio4
> > DMA modes: mdma0 mdma1 mdma2
> > UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
> > AdvancedPM=no WriteCache=enabled
> > Drive conforms to: device does not report version: 1 2 3 4 5
> >
> >
> >ATA device, with non-removable media
> > Model Number: WDC WD800JB-00CRA1
> > Serial Number: WD-WCA8E5325146
> > Firmware Revision: 17.07W17
> >Standards:
> > Supported: 5 4 3 2
> > Likely used: 6
> >Configuration:
> > Logical max current
> > cylinders 16383 16383
> > heads 16 16
> > sectors/track 63 63
> > --
> > CHS current addressable sectors: 16514064
> > LBA user addressable sectors: 156301488
> > device size with M = 1024*1024: 76319 MBytes
> > device size with M = 1000*1000: 80026 MBytes (80 GB)
> >Capabilities:
> > LBA, IORDY(can be disabled)
> > bytes avail on r/w long: 40 Queue depth: 1
> > Standby timer values: spec'd by Standard, with device specific minimum
> > R/W multiple sector transfer: Max = 16 Current = 16
> > Recommended acoustic management value: 128, current value: 254
> > DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
> > Cycle time: min=120ns recommended=120ns
> > PIO: pio0 pio1 pio2 pio3 pio4
> > Cycle time: no flow control=120ns IORDY flow control=120ns
> >Commands/features:
> > Enabled Supported:
> > * READ BUFFER cmd
> > * WRITE BUFFER cmd
> > * Host Protected Area feature set
> > * Look-ahead
> > * Write cache
> > * Power Management feature set
> > Security Mode feature set
> > * SMART feature set
> > * Device Configuration Overlay feature set
> > Automatic Acoustic Management feature set
> > SET MAX security extension
> > * DOWNLOAD MICROCODE cmd
> > * SMART self-test
> > * SMART error logging
> >Security:
> > supported
> > not enabled
> > not locked
> > not frozen
> > not expired: security count
> > not supported: enhanced erase
> >HW reset results:
> > CBLID- above Vih
> > Device num = 0 determined by CSEL
> >Checksum: correct
> >
> >lspci
> >00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3189
> >00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168
> >00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> >00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> >00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
> >00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
> >00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80)
> >00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80)
> >00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80)
> >00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
> >00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
> >00:11.1 IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE (rev 06)
> >00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
> >01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX] (rev b2)
> >
> >lspci -n
> >00:00.0 Class 0600: 1106:3189
> >00:01.0 Class 0604: 1106:b168
> >00:09.0 Class 0200: 10ec:8139 (rev 10)
> >00:0a.0 Class 0200: 10ec:8139 (rev 10)
> >00:0b.0 Class 0400: 109e:036e (rev 02)
> >00:0b.1 Class 0480: 109e:0878 (rev 02)
> >00:10.0 Class 0c03: 1106:3038 (rev 80)
> >00:10.1 Class 0c03: 1106:3038 (rev 80)
> >00:10.2 Class 0c03: 1106:3038 (rev 80)
> >00:10.3 Class 0c03: 1106:3104 (rev 82)
> >00:11.0 Class 0601: 1106:3177
> >00:11.1 Class 0101: 1106:0571 (rev 06)
> >00:11.5 Class 0401: 1106:3059 (rev 50)
> >01:00.0 Class 0300: 10de:0110 (rev b2)
> >
> >Im using RedHat 8.0 stock kernel (the updated version) 2.4.18-19.8.0.
> >
> > Regards Simon
> >
> >
> >-
> >To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> >the body of a message to majordomo@vger.kernel.org
> >More majordomo info at http://vger.kernel.org/majordomo-info.html
> >Please read the FAQ at http://www.tux.org/lkml/
> >
> >
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/