[1.] hpt372 - driver drops out using dma
[2.] I've just purchased an abit-kd7-raid with an integrated hpt372
controller. I've configured the kernel and experimented the system bios
and pci slot order settings many ways - allways with the same result:
after few random read accesses (movie or mp3 playing, copying files) my
maxtor ide drive simply fails to respond to any read or reset requests.
When i disable dma with hdparm -d0, the problem disappears, but that's a
bit expensive workaround. The system is working good with the 'official'
hpt372 generic scsi driver
(http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz), but i cannot
totally disable hpt372 recognition during bootup ('HPT372: detected
chipset, but driver not compiled in!') witch causes a very slow bootup
procedure caused by 'hde: lost interrupt'-s.
[3.] ide, hpt372
[4.] Linux version 2.4.20 (root@mcree) (gcc version 2.95.4 20011002
(Debian prerelease)) #7 2003. ápr. 4., péntek, 11.03.00 CEST
[5.]
output of hdparm -I /dev/hde _before_ the dropout:
-----8<-----------------------------------------------------------------------
/dev/hde:
non-removable ATA device, with non-removable media
Model Number: Maxtor 4G120J6
Serial Number: G60AQ60E
Firmware Revision: GAK819K0
Standards:
Supported: 1 2 3 4 5 6
Likely used: 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
bytes/track: 0 (obsolete)
bytes/sector: 0 (obsolete)
current sector capacity: 16514064
LBA user addressable sectors = 240121728
Capabilities:
LBA, IORDY(can be disabled)
Buffer size: 2048.0kB ECC bytes: 57 Queue depth: 1
Standby timer values: spec'd by standard, no device specific minimum
r/w multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 3
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* look-ahead
* write cache
* Power Management feature set
SMART feature set
SET MAX security extension
* Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
-----8<-----------------------------------------------------------------------
Output of hdparm -I /dev/hde _after_ the dropout:
-----8<-----------------------------------------------------------------------
/dev/hde:
removable ATA device, with non-removable media
Standards:
Likely used: 1
Configuration:
Logical max current
cylinders
heads
sectors/track
bytes/track:
bytes/sector:
LBA user addressable sectors = 0
Capabilities:
no IORDY
Cannot perform double-word IO
r/w multiple sector transfer: not supported
DMA: not supported
PIO: pio0
-----8<-----------------------------------------------------------------------
my syslog:
-----8<-----------------------------------------------------------------------
Apr 4 10:44:22 mcree kernel: hde: dma_intr: status=0xff { Busy }
Apr 4 10:44:22 mcree kernel: hde: DMA disabled
Apr 4 10:44:57 mcree kernel: ide2: reset timed-out, status=0xff
Apr 4 10:44:57 mcree kernel: hde: status timeout: status=0xff { Busy }
Apr 4 10:44:57 mcree kernel: hde: drive not ready for command
Apr 4 10:45:27 mcree kernel: ide2: reset timed-out, status=0xff
Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 58956
Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61700
Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61701
Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61702
Apr 4 10:45:27 mcree kernel: end_request: I/O error, dev 21:05 (hde), sector 61703
[...various errors resulting in 'filesystem panic'...]
-----8<-----------------------------------------------------------------------
slow bootup caused by unwanted hpt372 (and attached drive) recognition (i
turned off CONFIG_BLK_DEV_HPT34X in order to be able to use the 'official'
hpt driver, but i still want to use my primary vt8235 controller) - note
the 'lost interrupt'-s and the drive recognition:
-----8<-----------------------------------------------------------------------
Apr 4 11:36:01 mcree kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Apr 4 11:36:01 mcree kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Apr 4 11:36:01 mcree kernel: VP_IDE: IDE controller on PCI bus 00 dev 89
Apr 4 11:36:01 mcree kernel: VP_IDE: chipset revision 6
Apr 4 11:36:01 mcree kernel: VP_IDE: not 100%% native mode: will probe irqs later
Apr 4 11:36:01 mcree kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Apr 4 11:36:01 mcree kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
Apr 4 11:36:01 mcree kernel: ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio
Apr 4 11:36:01 mcree kernel: ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:DMA
Apr 4 11:36:01 mcree kernel: HPT372: IDE controller on PCI bus 00 dev 98
Apr 4 11:36:01 mcree kernel: HPT372: detected chipset, but driver not compiled in!
Apr 4 11:36:01 mcree kernel: HPT372: chipset revision 5
Apr 4 11:36:01 mcree kernel: HPT372: not 100%% native mode: will probe irqs later
Apr 4 11:36:01 mcree kernel: ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
Apr 4 11:36:01 mcree kernel: ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
Apr 4 11:36:01 mcree kernel: hda: ST360015A, ATA DISK drive
Apr 4 11:36:01 mcree kernel: hdc: ASUS CRW-1610A, ATAPI CD/DVD-ROM drive
Apr 4 11:36:01 mcree kernel: hdd: Pioneer DVD-ROM ATAPIModel DVD-106S 012, ATAPI CD/DVD-ROM drive
Apr 4 11:36:01 mcree kernel: hde: Maxtor 4G120J6, ATA DISK drive
Apr 4 11:36:01 mcree kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Apr 4 11:36:01 mcree kernel: ide1 at 0x170-0x177,0x376 on irq 15
Apr 4 11:36:01 mcree kernel: ide2 at 0xd800-0xd807,0xdc02 on irq 18
Apr 4 11:36:01 mcree kernel: blk: queue c03980c4, I/O limit 4095Mb (mask 0xffffffff)
Apr 4 11:36:01 mcree kernel: hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100)
Apr 4 11:36:01 mcree kernel: hde: lost interrupt
Apr 4 11:36:01 mcree last message repeated 3 times
Apr 4 11:36:01 mcree kernel: hde: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63
Apr 4 11:36:01 mcree kernel: Partition check:
Apr 4 11:36:01 mcree kernel: /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
Apr 4 11:36:01 mcree kernel: /dev/ide/host2/bus0/target0/lun0:hde: lost interrupt
Apr 4 11:36:01 mcree kernel: hde: lost interrupt
Apr 4 11:36:01 mcree kernel: p1 <hde: lost interrupt
Apr 4 11:36:01 mcree kernel: p5 >
Apr 4 11:36:01 mcree kernel: Floppy drive(s): fd0 is 1.44M
Apr 4 11:36:01 mcree kernel: FDC 0 is a post-1991 82077
Apr 4 11:36:01 mcree kernel: loop: loaded (max 8 devices)
-----8<-----------------------------------------------------------------------
The 'official' driver works ok. after the above 'slow boot':
-----8<-----------------------------------------------------------------------
Apr 4 11:36:01 mcree kernel: Device Driver for HPT37x2 ATA RAID Controller
Apr 4 11:36:01 mcree kernel: Version 1.31, Compiled Apr 4 2003 10:58:27
Apr 4 11:36:01 mcree kernel: Found Controller: HPT372 UDMA/ATA133 RAID Controller
Apr 4 11:36:01 mcree kernel: scsi1 : hpt37x2
Apr 4 11:36:01 mcree kernel: Vendor: Maxtor 4 Model: G120J6 Rev: GAK8
Apr 4 11:36:01 mcree kernel: Type: Direct-Access ANSI SCSI revision: 02
Apr 4 11:36:01 mcree kernel: Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Apr 4 11:36:01 mcree kernel: SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
Apr 4 11:36:01 mcree kernel: /dev/scsi/host1/bus0/target0/lun0: p1 < p5 >
-----8<-----------------------------------------------------------------------
[6.]
It was impossible not to reproduce the problem. 8)
The drive functioned properly for a small (but random) amount of time,
then crashed.
[7.]
[7.1.]
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux mcree 2.4.20 #7 2003. ápr. 4., péntek, 11.03.00 CEST i686 unknown
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.15
e2fsprogs 1.27
reiserfsprogs 3.x.1b
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 2.0.11
Modules Loaded hpt37x2 nvidia
[7.2.]
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(tm) XP 2100+
stepping : 1
cpu MHz : 1734.084
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 3460.30
[7.3.]
hpt37x2 55584 1
nvidia 1546144 10
[7.4.]
cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
c000-c0ff : Accton Technology Corporation EN-1216 Ethernet Adapter
c000-c0ff : tulip
c400-c43f : Ensoniq 5880 AudioPCI
c400-c43f : es1371
c800-c81f : VIA Technologies, Inc. USB
cc00-cc1f : VIA Technologies, Inc. USB (#2)
d000-d01f : VIA Technologies, Inc. USB (#3)
d400-d40f : VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
d400-d407 : ide0
d408-d40f : ide1
d800-d807 : Triones Technologies, Inc. HPT366/368/370/370A/372
d800-d807 : ide2
dc00-dc03 : Triones Technologies, Inc. HPT366/368/370/370A/372
dc02-dc02 : ide2
e000-e007 : Triones Technologies, Inc. HPT366/368/370/370A/372
e400-e403 : Triones Technologies, Inc. HPT366/368/370/370A/372
e800-e8ff : Triones Technologies, Inc. HPT366/368/370/370A/372
e800-e807 : ide2
e808-e80f : ide3
e810-e8ff : HPT372
cat /proc/iomem
00000000-0009efff : System RAM
0009f000-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000d0000-000d3bff : Extension ROM
000f0000-000fffff : System ROM
00100000-1ffeffff : System RAM
00100000-0029b44f : Kernel code
0029b450-0031d4f7 : Kernel data
1fff0000-1fff2fff : ACPI Non-volatile Storage
1fff3000-1fffffff : ACPI Tables
d0000000-dfffffff : PCI Bus #01
d0000000-d7ffffff : nVidia Corporation NV17 [GeForce4 MX440]
d8000000-d807ffff : nVidia Corporation NV17 [GeForce4 MX440]
e0000000-e3ffffff : PCI device 1106:3189 (VIA Technologies, Inc.)
e4000000-e5ffffff : PCI Bus #01
e4000000-e4ffffff : nVidia Corporation NV17 [GeForce4 MX440]
e6020000-e60203ff : Accton Technology Corporation EN-1216 Ethernet Adapter
e6020000-e60203ff : tulip
e6021000-e6021fff : Brooktree Corporation Bt878 Video Capture
e6021000-e6021fff : bttv
e6022000-e6022fff : Brooktree Corporation Bt878 Audio Capture
e6023000-e60230ff : VIA Technologies, Inc. USB 2.0
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
[7.5.]
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3189
Subsystem: ABIT Computer Corp.: Unknown device 1401
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b168 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e4000000-e5ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Accton Technology Corporation EN-1216 Ethernet Adapter (rev 11)
Subsystem: Standard Microsystems Corp [SMC]: Unknown device 1255
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min, 63750ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at e6020000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: Pinnacle Systems Inc.: Unknown device 0012
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e6021000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Multimedia controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: Pinnacle Systems Inc.: Unknown device 0012
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e6022000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at c400 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 80) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp.: Unknown device 1401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin C routed to IRQ 0
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc.: Unknown device 3104 (rev 82) (prog-if 20)
Subsystem: ABIT Computer Corp.: Unknown device 1401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 0
Region 0: Memory at e6023000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3177
Subsystem: VIA Technologies, Inc.: Unknown device 3177
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at d400 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 RAID bus controller: Triones Technologies, Inc. HPT366 / HPT370 (rev 05)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d800 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0171 (rev a3) (prog-if 00 [VGA])
Subsystem: ABIT Computer Corp.: Unknown device 8f00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at d8000000 (32-bit, prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
[7.6.]
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ASUS Model: CRW-1610A Rev: 1.10
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: PIONEER Model: DVD-ROM DVD-106 Rev: 1.22
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: Maxtor 4 Model: G120J6 Rev: GAK8
Type: Direct-Access ANSI SCSI revision: 02
[7.7.]
None.
Erno Rigo
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/